Miller Electric D-64 manual Wire Type, Size, And Feed Speed Capability Table, Motor Start Control

Page 18

4-6. Wire Type, Size, And Feed Speed Capability Table

	Motor Speed	Wire Type	Wire Size	Feed Speed Capability

	Standard	All	.023 To 5/64 in (0.6 To 2 mm)	50 To 780 ipm (1.3 To 19.8 mpm)

	Standard	All	3/32 To 7/64 in (2.4 To 2.8 mm)	50 To 700 ipm (1.3 To 17.8 mpm)

	Standard	All	1/8 in (3.2 mm)	50 To 300 ipm (1.3	To 7.6 mpm)

	Optional High	All	.023 To 5/64 in (0.6 To 2 mm)	92 To 1440 ipm (2.3	To 35.6 mpm)
	Speed	All	.023 To 5/64 in (0.6 To 2 mm)	92 To 1440 ipm (2.3	To 35.6 mpm)
	Speed

4-7. Motor Start Control

2

1

3

To change wire feed starting speed, proceed as follows:

Turn Off wire feeder and welding power source.

Remove wrapper.

1 Front Panel

Front panel shown open for illustra- tion purposes.

2 Left Side Inner Control Panel

It may be necessary to remove pan- el to access Motor Start Control. Remove panel only as far as re- quired if options are attached to panel.

3Motor Board PC1

4Motor Start Control Poten- tiometer R70

Turn potentiometer clockwise to in- crease time it takes the motor to ramp up to speed. Remove protec- tive white rubber cap before making adjustment. Adjust potentiometer R70 using a small nonconductive screwdriver.

Reinstall left side inner control pan- el if it was removed.

Reinstall wrapper.

Tools Needed:

Non-Conductive

1/4 in

Ref. 143 259-G / Ref. SB-183 121-C

OM-1582 Page 14

Image 18

Contents OM-1582 ProcessesDescription From Miller to You Table of Contents Directives StandardsArc Welding Hazards Symbol UsageMarks a special safety message Electric Shock can killFlying Metal can injure eyes ARC Rays can burn eyes and skinWelding can cause fire or explosion Buildup of GAS can injure or killPrincipal Safety Standards EMF Information About PacemakersUN Choc É Lectrique peut tuer Signification des symbolesConsignes DE Securite Lire Avant Utilisation LES Fumé ES ET LES GAZ peuvent ê tre dangereuxLE Soudage peut provoquer un incendie ou une explosion DES Particules Volantes peuvent blesser les yeuxLE Bruit peut affecter l’ouïe ’EMPLOI Excessif peut Risque D’INCENDIE OULA Chute DE L’APPAREIL peut blesser DES Organes Mobiles peuvent provoquer des blessuresPrincipales normes de sé curité Information sur les champs é lectromagné tiquesConsignes relatives aux stimulateurs cardiaques + + + DefinitionsSymbols And Definitions Rating Label For CE ProductsIntroduction InstallationSpecifications Site SelectionEquipment Connection Diagrams Gun Recommendation TableRear Panel Connections Pin Plug InformationPin Information Wire Type, Size, And Feed Speed Capability Table Motor Speed Wire Type Wire Size Feed Speed CapabilityMotor Start Control Rotating The Drive Assembly Installing And Threading Welding Wire To adjust drive roll pressure, hold nozzleOptional Equipment DIP Switch Settings Spot Time Range SelectionOption Interface Standard SettingsOperation Front Panel ControlsDisconnect power before maintaining Maintenance and TroubleshootingRoutine Maintenance Overload Protection And Optional Side Panel ControlsTroubleshooting Disconnect power before troubleshootingTrouble Remedy OM-1582 Electrical Diagram Circuit Diagram197 518-A Parts List Main AssemblyOptional Control Box Control Box -1 Item Panel, Front w/Components Panel, Front w/Components -2 Item Control Panel Drive Assembly, Wire Drive Assembly, Wire -1 Items 15 Drive Roll And Wire Guide Kits Fraction Metric Kit Roll Wire SizeRoll Drive OM-1582 Service SupportOwner’s Record Miller Electric Mfg. Co