Miller Electric M-10 Gun, 180, 140 Auto-Set manual Owner’s Record, Miller Electric Mfg. Co

Page 60

Owner’s Record

Please complete and retain with your personal records.

Model Name

Serial/Style Number

Purchase Date

(Date which equipment was delivered to original customer.)

 

 

Distributor

 

 

 

Address

 

 

 

City

 

 

 

State

Zip

 

 

For Service

Contact a DISTRIBUTOR or SERVICE AGENCY near you.

Always provide Model Name and Serial/Style Number.

Contact your Distributor for:

Welding Supplies and Consumables

 

Options and Accessories

 

Personal Safety Equipment

 

Service and Repair

 

Replacement Parts

 

Training (Schools, Videos, Books)

 

Technical Manuals (Servicing Information

 

and Parts)

 

Circuit Diagrams

 

Welding Process Handbooks

 

To locate a Distributor or Service Agency visit

 

www.millerwelds.com or call 1-800-4-A-Miller

 

 

 

Contact the Delivering Carrier to:

File a claim for loss or damage during

 

shipment.

 

For assistance in filing or settling claims, contact

 

your distributor and/or equipment manufacturer’s

 

Transportation Department.

 

PRINTED IN USA

2007 Miller Electric Mfg. Co. 2007−01

Miller Electric Mfg. Co.

An Illinois Tool Works Company

1635 West Spencer Street

Appleton, WI 54914 USA

International Headquarters−USA

USA Phone: 920-735-4505 Auto-Attended

USA & Canada FAX: 920-735-4134

International FAX: 920-735-4125

European Headquarters −

United Kingdom

Phone: 44 (0) 1204-593493

FAX: 44 (0) 1204-598066

www.MillerWelds.com

Image 60
Contents OM-225 311C ProcessesDescription File MIG GmawFrom Miller to You Table of Contents − Maintenance &TROUBLESHOOTING − Parts ListSymbol Usage Marks a special safety messageArc Welding Hazards Electric Shock can killARC Rays can burn eyes and skin Welding can cause fire or explosionFlying Metal can injure eyes Buildup of GAS can injure or killCalifornia Proposition 65 Warnings Principal Safety Standards EMF InformationAbout Pacemakers UNE Décharge Électrique peut entraîner la mort LES Fumées ET LES GAZ peuvent être dangereuxIndique un message de sécurité particulier LE Soudage peut provoquer un incendie ou une explosion DES Particules Volantes peuvent blesser les yeuxDES Pièces Chaudes peuvent provoquer des brûlures graves LE Bruit peut endommager l’ouïeRisque D’INCENDIE OU D’EXPLO LA Chute DE L’APPAREIL peut blesser’EMPLOI Excessif peut SUR DES Organes Mobiles peuvent provoquer des blessuresPrincipales normes de sécurité En ce qui concerne les stimulateurs cardiaques− Specifications SpecificationsVAC Model VAC Model w/Auto−SetEDuty Cycle And Overheating 115 VAC Model230 VAC Model OverheatingVolt-Ampere Curves Amperage− Installation Installing Welding GunIncorrect Work Cable Routing Inside Unit Process/Polarity TableChanging Polarity Installing Gas Supply Special installation may be Required where gasoline orVolatile liquids are present − See NEC Article 511 or CECDo not move or operate unit where it could tip Electrical Service Guide For 230 VAC Model Installing Wire Spool And Adjusting Hub TensionInput Voltage 230 Input Amperes At Rated Output Threading Welding Wire Remove gun nozzle and contact tipRemoving MIG Gun From Welding Power Source Cut Off End Of Wire Open Pressure Assembly KnobEnd Of Wire To Spool Installing Optional Spool Gun Switch In Welding Power Source OperationConnecting Spool Gun To Millermatic 140/180 − Operation Controls For 115 VAC Model w/Auto-SetEControls For 115 VAC Model 115VControls For 230 VAC Model 230VOM-225 311 Weld Parameter Chart For 115 VAC Model w/Auto−SetE 10/90 10/65 10/80 10/60 10/50 10/95 10/75 10/100 030 0.8 mm 035 0.9 mm Aluminum 100% Argon 4043ER10/32 OM-225 311 10/90 10/45 10/60 10/30 10/32 10/80 030 0.8 mm 035 0.9 mm#220179 #220179 #202926Dcep Dcen 100 10/60 10/45 10/40 10/20 10/50 024 0.6 mm #220179 030 0.8 mm #202926 035 0.9 mm 045 1.2 mm− Maintenance &TROUBLESHOOTING Routine MaintenanceOverload Protection Drive Motor ProtectionChanging Drive Roll Or Wire Inlet Guide Turn Off power before replacing contact tipReplacing Gun Contact Tip Cleaning Or Replacing Gun Liner Disconnect gun from unitTo Reassemble Gun Replacing Switch And/Or Head Tube Troubleshooting Table Trouble RemedyOM-225 311 − Electrical Diagram Circuit Diagram234 419-B − MIG Welding Gmaw Guidelines Typical MIG Process ConnectionsTypical MIG Process Control Settings Wire Recommendation Wire SpeedSelect Wire Size Select VoltageHolding And Positioning Welding Gun Conditions That Affect Weld Bead Shape Poor Weld Bead Characteristics Good Weld Bead CharacteristicsGun Movement During Welding Troubleshooting − Excessive Spatter Troubleshooting − PorosityPossible Causes Corrective Actions Troubleshooting − Excessive Penetration Troubleshooting − Lack Of PenetrationTroubleshooting − Incomplete Fusion Troubleshooting − Burn-Through Troubleshooting − Waviness Of BeadTroubleshooting − Distortion Common MIG Shielding Gases ApplicationFlat & Horizontal1 Fillet − Parts List Recommended Spare Parts Optional Drive Rolls OptionsPage Service SupportOwner’s Record Miller Electric Mfg. Co
Related manuals
Manual 60 pages 41.57 Kb