Agilent Technologies manual Index-2 85036B/E

Page 48

Index

when making connections, 3-6environmental requirements, 2-2equipment

required, 1-3

but not supplied, 1-3,6-2,6-5supplied, 1-2,6-2,6-4

ESD, 3-2precautions, 3-2,3-4supplies

part numbers, 6-5

when making connections, 3-6

F

female open, 3-9connecting, 3-9disconnecting, 3-9

frequency specifications, 2-4

frequency range, 2-4,4-3

G

gage connector

master, 6-5gage master

part numbers, 6-5gages, 1-3

H

handling, 3-10

history, calibration kit, 1-7humidity, 2-2

I

impedance system, A-4

incoming inspection, 1-4

inside diameter of outer conductor, specifications, 2-3inspection

damage, 3-3defects, 3-3incoming, 1-4mating plane, 3-3visual, 3-3

isopropyl alcohol

as cleaning solvent, 3-4

K

kit contents, 1-2overview, 1-2

return to Agilent, 5-3serial number, 1-6

L

label calibration, 4-3

part number, 6-5

limited calibration, 4-3limited calibration

requesting, 4-3loads

broadband, 1-2

M

maintenance, 3-2preventive, 1-8

maintenance of devices, 1-8making connections, 3-6manual

part number, 6-5mating plane

connector, 3-5

mating plane inspection, 3-3mating plane surfaces, 3-5mechanical specifications, 2-3

N

nitrogen, 3-4

nominal standard definitions, A-4numbers

serial, 1-6recording, 1-6

O

offices

sales and service, 5-3open-end wrench, 1-3,3-9

part number, 6-5opens, 1-2

opens and shorts, 1-2ordering parts, 6-2

P

part numbers, 6-2parts

ordering, 6-2replaceable, 6-2

required but not supplied, 6-2performance verification, 4-2

fail, 5-2

permanently stored calibration definitions, 1-3pin depth

typical values, 2-3

precision slotless connectors, 3-4preventive maintenance, 1-8

R

recertification, 4-3how often?, 4-3interval, 4-3limited, 4-3what’s included, 4-3

where to send your kit, 4-3regulations

environmental, 3-5replaceable parts, 6-2

Index-2

85036B/E

Image 48

Contents User’s and Service Guide Manufacturing Part Number Print Date JuneDocumentation Warranty Contents Replaceable Parts Standard DefinitionsGeneral Information Kit Contents Calibration Kit OverviewInstallation of the Calibration Definitions Calibration DefinitionsEquipment Required but Not Supplied AdaptersIncoming Inspection Calibration Kit Contents Recording the Device Serial Numbers Serial Number Record for 85036BSerial Number Record for 85036E Calibration Kits Documented in this Manual Calibration Kit HistoryAgilent 85036B kits with serial prefix 3102A and below Agilent 85036B kits with serial prefix 3103A and belowClarifying the Sex of a Connector Preventive MaintenanceSpecifications Temperature-What to Watch Out For Environmental RequirementsEnvironmental Requirements Mechanical Specifications Supplemental Mechanical CharacteristicsMechanical Specifications Mechanical CharacteristicsElectrical Specifications Electrical SpecificationsCertification Use, Maintenance, and Care of the Devices ESD Protection Setup Electrostatic DischargeWhat Causes Connector Wear? Visual InspectionLook for Obvious Defects and Damage First Inspect the Mating Plane SurfacesCleaning Connectors Inspect the Precision Slotless Connectors femaleUse Compressed Air or Nitrogen Clean the Mating Plane Surfaces ReinspectHow to Make a Connection Final Connection Using a Torque WrenchConnections Preliminary ConnectionTorque Wrench Information Wrench PositionsUsing the Torque Wrench How to Separate a Connection Connecting the Two-Piece Female OpenHandling and Storage Performance Verification Introduction How Agilent Verifies the Devices in This KitWhere to Send a Kit for Recertification RecertificationLimited Recertification How Often to RecertifyRecertification 85036B/E Troubleshooting Troubleshooting Process Troubleshooting FlowchartReturning a Kit or Device to Agilent Contacting AgilentReturning a Kit or Device to Agilent 85036B/E Replaceable Parts Replaceable Parts for the 85036B Calibration Kit AdaptersReplaceable Parts for the 85036B Calibration Kit Replaceable Parts for the 85036E Calibration Kit Miscellaneous Items Introduction 85036B/E Standard Definitions Standard Class Assignments Table A-1 Standard Class AssignmentsBlank Form Table A-2 Standard Class Assignments Blank FormSetting the System Impedance Nominal Standard Definitions Table A-3 Standard Definitions Standard b Offset FreqTable A-4 Standard Definitions Blank Form Index Index-2 85036B/E Calibration