Craftsman 320.2819 operating instructions Installing Router Motor in Base

Page 18

INSTALLING ROUTER MOTOR IN BASE

WARNING: NEVER use the router motor without installing it into either

a fixed or plunge approved base. Failure to do so could result in serious personal injury and damage to router motor.

NOTE: Before installing router motor in fixed base, have the collet/nut and router cutting bit you are going to use already installed in router motor. See

page 16 "INSTALLING AND REMOVING THE CUTTING BIT."

WARNING: ALWAYS turn router motor off and unplug router from power

source before making any adjustments or installing accessories. Failure to

turn router motor off and unplug router could result in accidental starting which can cause serious personal injury.

INSTALLING ROUTER MOTOR IN BASE (Fig_ 5)

1. Turn router motor off and

Fig. 5

unplug from power source.

2.Place fixed base on

flat surface.

F

,With back of fixed base facing you, open router motor clamp (A).

. Press in Coarse Adjust- ment Knob (B) while you align the router motor's slot with the pin in the fixed base.

5.When the router motDr's slot

is aligned and engaged into the base's pin, slide the router motor down base.

A

C

D

into the fixed

6.The router motor wilt now slide up or down to set coarse adjustments when the coarse adjustment knob is pressed in.

7.After all adjustments are made, close the router motor clamp securely.

REMOVING ROUTER MOTOR FROM BASE (Fig. 5)

1.Turn router motor off and unplug from power source. 2_ Place router (fixed base/router motor) on flat surface_

3.With back of router facing you, open the router motor clamp (A).

4.Push in coarse adjustment knob (B) to release router motor "Position groove"

(C)from lock hook (D) in base, while you lift router motor free of base.

5.Set motor upside down on its top cap with collet pointing up and remove cut- ting bit. Store motor and base in carry bag when not being used.

28190 ManuaLRevised_0743409

Page 18

Page 17 Page 19
Image 18
Page 17 Page 19
Contents Sears, Roebuck and Co., Hoffman Estates, IL Reproductive harm Read ALL InstructionsSymbol Meanings Damage Prevention and Information MessagesWork Area Safety Personal SafetyTool USE and Care Precautions when operating this tool Extension CordsSafety Symbols for Your Tool Service SafetySafety Rules for Router Disconnect the Tool from Power Source before making any Table, large bits should be used for edging onlyoAvoid Climb CUTTING. See Operation section in this manual Additional Rules for Safe Operation28$90 ManuaLRevised0743409 ManuaLRevised On/Off Switch Know Your Fixed Base Router FigOperating features and safety requirements Yourself with all Selecting the Cutting BIT ING the Cutting BIT Figs Instalung the Cutting BITCOLLET/NUT Care Cutting BitsInstalling Router Motor in Base Adjusting Depth of CUT Coarse AdjustmentMicro Adjustments Ring E To Adjust Depth Figs 6 and 6a Soft Start Feature Deep CutsTorque twist, customa.,-y in larger router HEAVY-DUTY Edge Live Tool IndicatorLED Worklights Fig Guide FigElectronic Variable Speed Control Detachable Power Cord FigDial Setting ApplicationPlacing the Router Onto the Workpiece and Starting the CUT Edge Routing or Internal RoutingAkWARNING Removing Cutting Bit from Work Control CausingBoth Personal injuryFreehand Routing with the Fixed Base Fig. i Edging wrrH a Pilot BIT Feeding the Router Fig Ternal Cuts FigDirection of FEED., Internal Cuts Figs. ! 7 nd 17a An internal cutFeeding TOO Fast Fig Feeding TOO Slow aDust Collection with Dust Chip Shield Deflector FigAlways Extraction AID Ppter FigTo adjust Depth with the Depth-Adjustment Wrenc Fig Routine Maintenance GeneralReplacement of Carbon Brushes Fig Same way they came out This will avoid a break4qperiodLubrication Installed Ion of Craftsman router ac Accessories Fixed Base Router Motor Unit 3520!30000 370384100028i 3122924000Mo,,,t!ngPlate 28190ManuaLRevisecl07-0409Page43 Your Home CenterWv,w.sears,com
Top Page Image Contents