Craftsman 320.2819 Adjusting Depth of CUT, Coarse Adjustment, Micro Adjustments Ring E

Page 19

WARNING: ALWAYS remove cutting bits from collet/nut when the router is not being used. Leaving bits installed could result in an accident causing serious personal injury.

ADJUSTING DEPTH OF CUT

WARNING: Your router should NEVER BE TURNED ON or be connected

to the power source when you are assembling parts, making adjustments, installing or removing collets / nuts, cutting bits, cleaning or when it is not in

use. Disconnecting the router will prevent accidental starting, which could cause serious personal injury.

NOTE: All depth adjustments on the Fixed Base must be made with the mo- tor clamp open.

NOTE: For all Fixed Base Routers, the cutting bit depth equals the amount of the cutter that is exposed below the surface of the sub-base.

The fixed base is designed with a micrometer fine adjustment system. When the bit is lowered to the approximate position desired (coarse setting), the system then can be micro adjusted to the precise depth.

Coarse Adjustment:

Depressing the Coarse Adjustment Knob (B) allows you to quickly lower or raise the cutting bit to three depth settings.

Micro Adjustments:

NOTE: Before making fine adjustments, reset zero "0" on Depth Indicator

Ring (E, Fig.5).

The Depth Indicator Ring (E, Fig.5) located on the Fine Adjustment Dial (F, Fig° 5) is marked incrementally in 64ths. Turning the fine adjustment dial clockwise 180 ° (1/2 turn), lowers the cutting bit 1/16 inch. One full turn clockwise (360 °) zero "0" to zero "0" lowers the bit 1/8 in.

The Depth Indicator Ring may be reset to zero "0" without moving the Fine Adjust- ment Dial. This allows the user to begin adjustments from any reference point desired

28190 ManuaLRevised_07-0409

Page 19

Page 18 Page 20
Image 19
Page 18 Page 20
Contents Sears, Roebuck and Co., Hoffman Estates, IL Read ALL Instructions Reproductive harmDamage Prevention and Information Messages Symbol MeaningsPersonal Safety Work Area SafetyTool USE and Care Extension Cords Precautions when operating this toolService Safety Safety Symbols for Your ToolSafety Rules for Router Table, large bits should be used for edging onlyo Disconnect the Tool from Power Source before making anyAdditional Rules for Safe Operation Avoid Climb CUTTING. See Operation section in this manual28$90 ManuaLRevised0743409 ManuaLRevised Know Your Fixed Base Router Fig On/Off SwitchYourself with all Operating features and safety requirementsSelecting the Cutting BIT Instalung the Cutting BIT ING the Cutting BIT FigsCutting Bits COLLET/NUT CareInstalling Router Motor in Base Coarse Adjustment Adjusting Depth of CUTMicro Adjustments Ring E To Adjust Depth Figs 6 and 6a Deep Cuts Soft Start FeatureTorque twist, customa.,-y in larger router Guide Fig Live Tool IndicatorLED Worklights Fig HEAVY-DUTY EdgeApplication Detachable Power Cord FigDial Setting Electronic Variable Speed ControlEdge Routing or Internal Routing Placing the Router Onto the Workpiece and Starting the CUTPersonal injury Control CausingBoth AkWARNING Removing Cutting Bit from WorkFreehand Routing with the Fixed Base Fig. i Edging wrrH a Pilot BIT Ternal Cuts Fig Feeding the Router FigAn internal cut Direction of FEED., Internal Cuts Figs. ! 7 nd 17aFeeding TOO Slow a Feeding TOO Fast FigExtraction AID Ppter Fig Chip Shield Deflector FigAlways Dust Collection with DustTo adjust Depth with the Depth-Adjustment Wrenc Fig General Routine MaintenanceSame way they came out This will avoid a break4qperiod Replacement of Carbon Brushes FigLubrication Installed Ion of Craftsman router ac Accessories Fixed Base Router Motor Unit 3703841000 3520!3000028i 3122924000Mo,,,t!ngPlate 28190ManuaLRevisecl07-0409Page43 Center Your HomeWv,w.sears,com
Top Page Image Contents