Cisco Systems OL-1911-05 ATM Switch Router Ethernet Interface, Router 2 Ethernet Interface, 24-14

Page 14

Chapter 24 Configuring ATM Router Module Interfaces

Configuring LECs on ATM Router Module Interfaces (Catalyst 8540 MSR)

Router 1 ATM Interface

Router1# configure terminal

Router1(config)# interface atm 2/0

Router1(config-if)#ip address 1.0.0.1 255.0.0.0

Router1(config-if)# atm pvc 1 0 5 qsaal

Router1(config-if)# atm pvc 2 0 16 ilmi

Router1(config-if)#lane client ethernet happy

Router1(config-if)# end

Router1#

ATM Switch Router ATM Router Module Interface

Switch# configure terminal

Switch(config)# interface atm 2/0/0

Switch(config-if)#ip address 1.0.0.2 255.0.0.0

Switch(config-if)#lane client ethernet BACKBONE

Switch(config-if)# end

Switch#

ATM Switch Router Ethernet Interface

Switch# configure terminal

Switch(config)# interface gigabitethernet 9/0/0

Switch(config-if)#ip address 129.1.0.1 255.255.255.0

Switch(config-if)#no ip directed-broadcast

Switch(config-if)# end

Switch#

Router 2 Ethernet Interface

Router2# configure terminal

Router2(config)# interface gigabitethernet 9/0/0

Router2(config-if)#ip address 129.1.0.2 255.255.255.0

Router2(config-if)#no ip directed-broadcast

Router2(config-if)# end

Router2#

Configure the desired network routing protocol, such as RIP, OSPF, or EIGRP, on Ethernet interfaces. For more information on configuring networking protocols and routing, refer to the Layer 3 Software Configuration Guide.

	ATM and Layer 3 Switch Router Software Configuration Guide
24-14	OL-1911-05

Image 14

Contents Configuring ATM Router Module Interfaces 24-1Overview of the ATM Router Module 24-2Catalyst 8540 MSR Enhanced ATM Router Module Features 24-3Catalyst 8540 MSR ATM Router Module Features 24-4Hardware Restrictions 24-524-6 Catalyst 8540 MSR ATM Router Module Software Restrictions 24-7Ssrp 24-8Configuring ATM Router Module Interfaces 24-9Switchconfig# interface atm 0/0/0 Manual ATM Router Module Interface ConfigurationCommand Purpose Example24-11 Card /subcard /port .subinterface# multipointElan-name 24-12 LEC Configuration ExamplesLane Routing Over ATM Router 1 ATM Interface ATM Switch Router ATM Router Module InterfaceLane Routing from ATM to Ethernet Router 2 ATM Interface24-14 ATM Switch Router Ethernet InterfaceRouter 2 Ethernet Interface 24-15 Lane Bridging Between ATM and EthernetRouter 1 Bridge Interface Router 2 Bridge Interface Configuring Multiprotocol Encapsulation over ATMConfirming the LEC Configuration 24-16Upc upc encap aal5mux 1 aal5snap Pd pd rx-cttr index tx-cttr index interfaceAtm card /subcard /port .vpt# vpi-b vci-b Atm-nsap address atm-vc vci broadcastRouter with ATM Interface Multiprotocol Encapsulation over ATM Configuration ExampleATM Switch Router 24-18Card /subcard /port vpi vci encap aal5mux Switchconfig-if# atm pvc 2 vci interface atmEthernet Router Aal5snap inarp minutesCard /subcard /port internal Configuring as an ATM ARP ClientNsap-address 24-20ESI Example Client Aconfig# interface atm 1/0/0Nsap Address Example 24-21Minutes Configuring as an ATM ARP ServerSwitchconfig-if# atm arp-server time-out 24-22Switch# show atm map Displaying the IP-over-ATM Interface ConfigurationSwitch# show atm arp-server ExamplesSwitchconfig# bridge number protocol ieee Configuring BridgingSwitchconfig# interface fastethernet 24-24Switchconfig-if# atm pvc 2 vci-A interface atm Configuring Packet Flooding on a PVCSwitchconfig-if# no ip directed-broadcast Broadcast24-26 Displaying the Bridging ConfigurationShow bridge verbose About Rate Limiting Configuring IP MulticastSwitchconfig# ip multicast-routing Vpi-b vci-b upc upc encap aal5snapRestrictions Configuring Rate LimitingFeatures Supported Rate-limit input output rate burstRouter# configure terminal 24-2924-30