Cisco Systems OL-1911-05 manual Configuring Packet Flooding on a PVC, Broadcast, 24-25

Page 25

Chapter 24 Configuring ATM Router Module Interfaces

Configuring Bridging

Switch(config)# interface atm 3/0/0

Switch(config-if)#atm pvc 2 200 interface atm 1/0/0 0 200

Switch(config-if)# bridge-group 5

Switch(config-if)# end

Switch(config)# interface fastethernet 0/0/0

Switch(config-if)# no cdp enable

Switch(config-if)# bridge-group 5

Switch(config-if)# end

Switch(config)# bridge 5 protocol ieee

Configuring Packet Flooding on a PVC

Typically, a specific static map list configuration is not required for bridging to occur. In case of packet flooding, the bridging mechanism individually sends the packet to be flooded on all PVCs configured on the interface. To restrict the broadcast of the packets to only a subset of the configured PVCs you must define a separate static map list. Use the broadcast keyword in the static-mapcommand to restrict packet broadcasting.

 

Command

Purpose

Step 1

 

 

Switch(config)# interface atm card/subcard/port

Specifies the interface to configure on the ATM

 

Switch(config-if)#

router module.

 

 

Step 2

 

 

Switch(config-if)# no ip address

Disables IP processing.

Step 3

 

 

Switch(config-if)#no ip directed-broadcast

Disables the translation of directed broadcasts to

 

 

physical broadcasts.

Step 4

 

 

Switch(config-if)# map-groupnumber

Enters the map group name associated with this

 

 

PVC.

 

 

 

Step 5 Switch(config-if)#atm pvc 2 vci-Ainterface atm

Configures a PVC.

 

card/subcard/port vpi-B

Note The VPI number on the ATM router

 

 

 

 

module interface must be 2.

Step 6

 

 

Switch(config-if)# bridge-groupnumber

Assigns the interface to a bridge group.

Step 7

 

 

Switch(config-if)# end

Returns to global configuration mode.

 

Switch(config)#

 

Step 8

 

 

Switch(config)# map-listname

Creates a map list by naming it, and enters

 

Switch(config-map-list)#

map-list configuration mode.

 

 

Step 9

 

 

Switch(config-map-list)# bridge atm-vcnumber

Enables packet flooding on a PVC.

 

broadcast

 

 

 

 

 

 

ATM and Layer 3 Switch Router Software Configuration Guide

 

 

 

 

 

 

OL-1911-05

 

 

24-25

 

 

 

 

 

Image 25
Contents 24-1 Configuring ATM Router Module Interfaces24-2 Overview of the ATM Router Module24-3 Catalyst 8540 MSR Enhanced ATM Router Module Features24-4 Catalyst 8540 MSR ATM Router Module Features24-5 Hardware Restrictions24-6 24-7 Catalyst 8540 MSR ATM Router Module Software Restrictions24-8 Ssrp24-9 Configuring ATM Router Module InterfacesCommand Purpose Manual ATM Router Module Interface ConfigurationSwitchconfig# interface atm 0/0/0 ExampleElan-name Card /subcard /port .subinterface# multipoint24-11 Lane Routing Over ATM LEC Configuration Examples24-12 Lane Routing from ATM to Ethernet ATM Switch Router ATM Router Module InterfaceRouter 1 ATM Interface Router 2 ATM InterfaceRouter 2 Ethernet Interface ATM Switch Router Ethernet Interface24-14 Router 1 Bridge Interface Lane Bridging Between ATM and Ethernet24-15 Confirming the LEC Configuration Configuring Multiprotocol Encapsulation over ATMRouter 2 Bridge Interface 24-16Atm card /subcard /port .vpt# vpi-b vci-b Pd pd rx-cttr index tx-cttr index interfaceUpc upc encap aal5mux 1 aal5snap Atm-nsap address atm-vc vci broadcastATM Switch Router Multiprotocol Encapsulation over ATM Configuration ExampleRouter with ATM Interface 24-18Ethernet Router Switchconfig-if# atm pvc 2 vci interface atmCard /subcard /port vpi vci encap aal5mux Aal5snap inarp minutesNsap-address Configuring as an ATM ARP ClientCard /subcard /port internal 24-20Nsap Address Example Client Aconfig# interface atm 1/0/0ESI Example 24-21Switchconfig-if# atm arp-server time-out Configuring as an ATM ARP ServerMinutes 24-22Switch# show atm arp-server Displaying the IP-over-ATM Interface ConfigurationSwitch# show atm map ExamplesSwitchconfig# interface fastethernet Configuring BridgingSwitchconfig# bridge number protocol ieee 24-24Switchconfig-if# no ip directed-broadcast Configuring Packet Flooding on a PVCSwitchconfig-if# atm pvc 2 vci-A interface atm BroadcastShow bridge verbose Displaying the Bridging Configuration24-26 Switchconfig# ip multicast-routing Configuring IP MulticastAbout Rate Limiting Vpi-b vci-b upc upc encap aal5snapFeatures Supported Configuring Rate LimitingRestrictions Rate-limit input output rate burst24-29 Router# configure terminal24-30