Cisco Systems OL-1911-05 manual 24-6

Page 6

Chapter 24 Configuring ATM Router Module Interfaces

Hardware and Software Restrictions of the ATM Router Module

Catalyst 8540 MSR Enhanced ATM Router Module Software Restrictions

The following software restrictions apply to the Catalyst 8540 MSR enhanced ATM router module:

LANE is not supported.

LANE Clients are not supported.

Use tag switching functionality with caution. Do not distribute routes learned through tag switching to Fast Ethernet (FE) or Gigabit Ethernet (GE), or vice versa. Otherwise, you might have unreachable route destinations.

The ATM router module does not initialize if it replaces an ATM port adapter or interface module when hierarchical VP tunnels are globally enabled. Reboot the switch to initialize the ATM router module.

IP multicast is only supported over 1483 LLC/SNAP encapsulated PVCs.

ATM Director does not support any PVC commands.

Even though each ATM router module interface supports a maximum of 2048 VCs, only 1400 to 1500 external VCs can be configured. Internal VCs use up the rest.

Do not install an ATM router module in a slot pair where hierarchical VP tunnels are configured. Slot pairs 0 and 1, 2 and 3, 9 and 10, and 11 and 12 use the same switching modules for scheduling. For example, do not install an ATM router module in slot 10 when hierarchical VP tunnels are configured on slot 9. For more information on hierarchical VP tunneling restrictions, see Chapter 6, “Configuring Virtual Connections.”

The Catalyst 8540 MSR enhanced ATM router modules do not support the following features:

Tag-edged router functionality

Fast Simple Server Redundancy Protocol (FSSRP)

Bridging for multiplexing device encapsulation

Protocol Independent Multicast (PIM) IP multipoint signalling

PIM nonbroadcast multiaccess (NBMA)

PIM over ATM multipoint signalling

Translation from IP quality of service (QoS) to ATM QoS

Resource Reservation Protocol (RSVP) to ATM SVC

PVC management using ILMI

IP multicast over RFC 1483 SVCs

Access lists for ATM to ATM routing

Half-bridge devices

Layer 2 ACLs

ATM and Layer 3 Switch Router Software Configuration Guide

24-6

OL-1911-05

 

 

Image 6
Contents Configuring ATM Router Module Interfaces 24-1Overview of the ATM Router Module 24-2Catalyst 8540 MSR Enhanced ATM Router Module Features 24-3Catalyst 8540 MSR ATM Router Module Features 24-4Hardware Restrictions 24-524-6 Catalyst 8540 MSR ATM Router Module Software Restrictions 24-7Ssrp 24-8Configuring ATM Router Module Interfaces 24-9Switchconfig# interface atm 0/0/0 Manual ATM Router Module Interface ConfigurationCommand Purpose ExampleCard /subcard /port .subinterface# multipoint Elan-name24-11 LEC Configuration Examples Lane Routing Over ATM24-12 Router 1 ATM Interface ATM Switch Router ATM Router Module InterfaceLane Routing from ATM to Ethernet Router 2 ATM InterfaceATM Switch Router Ethernet Interface Router 2 Ethernet Interface24-14 Lane Bridging Between ATM and Ethernet Router 1 Bridge Interface24-15 Router 2 Bridge Interface Configuring Multiprotocol Encapsulation over ATMConfirming the LEC Configuration 24-16Upc upc encap aal5mux 1 aal5snap Pd pd rx-cttr index tx-cttr index interfaceAtm card /subcard /port .vpt# vpi-b vci-b Atm-nsap address atm-vc vci broadcastRouter with ATM Interface Multiprotocol Encapsulation over ATM Configuration ExampleATM Switch Router 24-18Card /subcard /port vpi vci encap aal5mux Switchconfig-if# atm pvc 2 vci interface atmEthernet Router Aal5snap inarp minutesCard /subcard /port internal Configuring as an ATM ARP ClientNsap-address 24-20ESI Example Client Aconfig# interface atm 1/0/0Nsap Address Example 24-21Minutes Configuring as an ATM ARP ServerSwitchconfig-if# atm arp-server time-out 24-22Switch# show atm map Displaying the IP-over-ATM Interface ConfigurationSwitch# show atm arp-server ExamplesSwitchconfig# bridge number protocol ieee Configuring BridgingSwitchconfig# interface fastethernet 24-24Switchconfig-if# atm pvc 2 vci-A interface atm Configuring Packet Flooding on a PVCSwitchconfig-if# no ip directed-broadcast BroadcastDisplaying the Bridging Configuration Show bridge verbose24-26 About Rate Limiting Configuring IP MulticastSwitchconfig# ip multicast-routing Vpi-b vci-b upc upc encap aal5snapRestrictions Configuring Rate LimitingFeatures Supported Rate-limit input output rate burstRouter# configure terminal 24-2924-30