Cisco Systems A9014CFD, ASR 9014CFD manual Grounding Point

Page 34

Chapter 3 Installing the Cisco ASR 901 Mobile Wireless Router

Mounting the Cisco ASR 901 Router

Warning This equipment must be grounded. Never defeat the ground conductor or operate the equipment in the absence of a suitably installed ground conductor. Contact the appropriate electrical inspection authority or an electrician if you are uncertain that suitable grounding is available. Statement 1024

Warning Use copper conductors only. Statement 1025

Warning When installing the unit, the ground connection must always be made first and disconnected last. Statement 42

Figure 3-3shows the grounding point marked on the rear panel of the Cisco ASR 901 router for ease of installation

Figure 3-3

Grounding Point

282342

1

2

1Fan

2Grounding Point Lug

This unit is to be installed in a restrictive access location and must be permanently grounded to minimum 6-AWG copper ground wire.

Complete the following steps to ground the Cisco ASR 901 router using a 2-hole lug and the corresponding mounting point. Most carriers require a 6-AWG ground connection. Verify your carrier’s requirements for the ground connection.

Step 1 In the accessory kit, locate the 2-hole lug, 2 pan-head Phillips head screws used to attach the lug to the router, and 6-AWG ground wire. (Lug, screws, and wire are part number 32-0629-01.)

Step 2 Set the parts aside.

Step 3 If your ground wire is insulated, use a wire-stripping tool to strip the ground wire to 0.5 inch ± 0.02 inch (12.7 mm ±0.5 mm) for the ring terminal (Figure 3-4).

.

Cisco ASR 901 Series Aggregation Services Router Hardware Installation Guide

3-6

OL-23778-01

 

 

Image 34
Contents Americas Headquarters Text Part Number OL-23778-01Page N T E N T S Required Tools and Equipment Troubleshooting A-1 OL-23778-01 Document Revision History Revision Date Change SummaryOrganization ObjectivesAudience ConventionsSafety Warnings Related DocumentationAbout This Guide Introduction Hardware DescriptionCisco ASR 901 Router Front View Cisco ASR 901 Router Ethernet Version Front View Cisco ASR 901 Router-Front ViewCisco ASR 901 Router Rear View Fan Grounding Point LugSpecification Value Power SupplySafety Precautions LEDsPin Connector a Pin Connector BDescription Specification Environmental Monitoring Temperature SensorSystem Specifications Router Interface NumberingRegulatory Compliance Interface Number Location LabelSafety Guidelines Safety with EquipmentSafety with Electricity Preventing Electrostatic Discharge Damage Site Planning Power Supply ConsiderationsPrerequisites Site EnvironmentMethod of Procedure Air Flow GuidelinesUnpacking and Checking the Contents of your Shipment Required Tools and EquipmentInstallation Checklist Task Verified by DateConsole Port Connections Console Port ConsiderationsCreating a Site Log Task Verified byPreparing to Install the Router Console Port Considerations OL-23778-01 Installing the Cisco ASR 901 Mobile Wireless Router Network ModulesRack-Mounting Configuration Guidelines Mounting the Cisco ASR 901 RouterAttaching the Rack-Mounting Brackets Mounting the Cisco ASR 901 Router in a RackAttaching the Cable Guides Connecting the Chassis Ground and Power Grounding the Cisco ASR 901 RouterGrounding Point Power Connection Compliance Stripping a Ground WireWiring the DC-Input Power Source 6-Pin Terminal BlockInstalling and Removing SFP Modules Installing SFP ModulesInstalling an SFP Module into an SFP Module Slot Removing SFP ModulesConnecting Cables Connecting the Console PortTypes of RJ-45 Cables Console PortConnecting Gigabit Ethernet Interface Cables Connecting the Network CablesConnecting T1 and E1 Interface Cables Connecting Cables to the Bits Interface Connecting SFP CablesConnecting GPS Cables Connecting to the Management Ethernet Port Powering On the RouterConnecting to Alarm Port Dressing Router CablesFormatting Procedures for Flash Memory Checklist for Power UpPower-On Procedure Interpreting Front-Panel LEDsDisplaying Contents of the Flash Memory File and Directory ProceduresCopying Files Displaying File Content Deleting Files from the Flash MemoryWhat to Do After Installing the Hardware Enter a Directory and Determine the Current DirectoryOL-23778-01 Troubleshooting Problem SolvingEnvironmental Reporting Features Troubleshooting the Power and Cooling SystemsSymptom Possible Cause Corrective Action Troubleshooting Cables, and Connections Information Packet publicationCopper GE from Quad combo PHY ports contain Two Leds each Reading the LEDsChassis LEDs System LEDRJ-45 Ethernet Interface LEDs T1/E1 Interface LEDsSFP Ethernet Interface LEDs Color/State Description two LEDs for each T1/E1 portOL-23778-01 Cable Specifications Gigabit Ethernet Connector PinoutsPin FE Signal GE Signal SFP Port Pinouts and Cable SpecificationsT1/E1 Port Pinouts Console Port Signals and Pinouts Console Port Signals and PinoutsPin Signal Name Direction Description Pin Signal Name HP Pins Direction Description RJ-45-to-DB-9 Terminal Adapter ConsoleIdentifying a Rollover Cable Terminal Adapter Device Signal RJ-45 Pin DB-25 PinConsole RJ-45-to-DB-25 Port DTE Time of Day Pinouts Bits Port PinoutsGPS Port Pinouts Management Ethernet Port Pinouts Alarm Port PinoutsPin Signal Name Description 10 MhzRxDP RxDN TxDP Not connected TxDN Site Log Date InitialsNumerics IN-2 IN-3 IN-4
Related manuals
Manual 884 pages 9.83 Kb