Cisco Systems ASR 9014CFD, A9014CFD manual Wiring the DC-Input Power Source, Pin Terminal Block

Page 36

Chapter 3 Installing the Cisco ASR 901 Mobile Wireless Router

Mounting the Cisco ASR 901 Router

Wiring the DC-Input Power Source

Warning This product relies on the building’s installation for short-circuit (overcurrent) protection. Ensure that the protective device is rated not greater than 10 A minimum, 60 VDC. Statement 1005

Complete the following steps to connect the DC power supply to the Cisco ASR 901 router:

Step 1 Switch off the DC power source at the circuit breaker, and place the circuit breaker in the Off position.

Step 2 Locate the 6-pin terminal block (part number 27-2030-01) (Figure 3-6). The terminal block is located in the accessory kit (part number 53-3085-01 for the Cisco ASR 901 router), which is shipped with the router.

Figure 3-6 6-Pin Terminal Block

282346

Step 3 Plug the 6-pin terminal block into the power connector located on the front side of the router.

Step 4 Connect one end of the customer-supplied power cord (16-AWG copper wire) to the site DC power source.

Step 5 Plug the connector on the power supply cord into the 6-pin terminal block that you plugged into the rear of the router in Step 3.

Warning An exposed wire lead from a DC-input power source can conduct harmful levels of electricity. Be sure that no exposed portion of the DC-input power source wire extends from the terminal block plug. Statement 122

Warning When installing this unit, secure all power cabling to avoid disturbing field-wiring connections. Statement 38

Caution DO NOT power on the unit yet.

Cisco ASR 901 Series Aggregation Services Router Hardware Installation Guide

3-8	OL-23778-01

Image 36

Contents Americas Headquarters Text Part Number OL-23778-01Page N T E N T S Required Tools and Equipment Troubleshooting A-1 OL-23778-01 Document Revision History Revision Date Change SummaryObjectives AudienceOrganization ConventionsSafety Warnings Related DocumentationAbout This Guide Introduction Hardware DescriptionCisco ASR 901 Router Front View Cisco ASR 901 Router Ethernet Version Front View Cisco ASR 901 Router-Front ViewCisco ASR 901 Router Rear View Fan Grounding Point LugPower Supply Safety PrecautionsSpecification Value LEDsPin Connector a Pin Connector BEnvironmental Monitoring Temperature Sensor System SpecificationsDescription Specification Router Interface NumberingRegulatory Compliance Interface Number Location LabelSafety Guidelines Safety with EquipmentSafety with Electricity Preventing Electrostatic Discharge Damage Power Supply Considerations PrerequisitesSite Planning Site EnvironmentMethod of Procedure Air Flow GuidelinesUnpacking and Checking the Contents of your Shipment Required Tools and EquipmentInstallation Checklist Task Verified by DateConsole Port Considerations Creating a Site LogConsole Port Connections Task Verified byPreparing to Install the Router Console Port Considerations OL-23778-01 Installing the Cisco ASR 901 Mobile Wireless Router Network ModulesRack-Mounting Configuration Guidelines Mounting the Cisco ASR 901 RouterAttaching the Rack-Mounting Brackets Mounting the Cisco ASR 901 Router in a RackAttaching the Cable Guides Connecting the Chassis Ground and Power Grounding the Cisco ASR 901 RouterGrounding Point Power Connection Compliance Stripping a Ground WireWiring the DC-Input Power Source 6-Pin Terminal BlockInstalling and Removing SFP Modules Installing SFP ModulesInstalling an SFP Module into an SFP Module Slot Removing SFP ModulesConnecting Cables Connecting the Console PortTypes of RJ-45 Cables Console PortConnecting the Network Cables Connecting Gigabit Ethernet Interface CablesConnecting T1 and E1 Interface Cables Connecting SFP Cables Connecting Cables to the Bits InterfaceConnecting GPS Cables Powering On the Router Connecting to Alarm PortConnecting to the Management Ethernet Port Dressing Router CablesChecklist for Power Up Power-On ProcedureFormatting Procedures for Flash Memory Interpreting Front-Panel LEDsFile and Directory Procedures Displaying Contents of the Flash MemoryCopying Files Displaying File Content Deleting Files from the Flash MemoryWhat to Do After Installing the Hardware Enter a Directory and Determine the Current DirectoryOL-23778-01 Troubleshooting Problem SolvingTroubleshooting the Power and Cooling Systems Environmental Reporting FeaturesSymptom Possible Cause Corrective Action Troubleshooting Cables, and Connections Information Packet publicationReading the LEDs Chassis LEDsCopper GE from Quad combo PHY ports contain Two Leds each System LEDT1/E1 Interface LEDs SFP Ethernet Interface LEDsRJ-45 Ethernet Interface LEDs Color/State Description two LEDs for each T1/E1 portOL-23778-01 Cable Specifications Gigabit Ethernet Connector PinoutsSFP Port Pinouts and Cable Specifications Pin FE Signal GE SignalT1/E1 Port Pinouts Console Port Signals and Pinouts Console Port Signals and PinoutsPin Signal Name Direction Description Pin Signal Name HP Pins Direction Description RJ-45-to-DB-9 Terminal Adapter ConsoleTerminal Adapter Device Signal RJ-45 Pin DB-25 Pin Identifying a Rollover CableConsole RJ-45-to-DB-25 Port DTE Bits Port Pinouts Time of Day PinoutsGPS Port Pinouts Alarm Port Pinouts Pin Signal Name DescriptionManagement Ethernet Port Pinouts 10 MhzRxDP RxDN TxDP Not connected TxDN Site Log Date InitialsNumerics IN-2 IN-3 IN-4

Related manuals

Manual 884 pages 9.83 Kb