Cisco Systems ASR 9014CFD manual SFP Port Pinouts and Cable Specifications, T1/E1 Port Pinouts

Page 56

Appendix B Cable Specifications

SFP Port Pinouts and Cable Specifications

Table B-1		RJ-45 Connector Pinouts

Pin	FE Signal		GE Signal

3	RX data+		RX B+

4	Not used		TX C+

5	Not used		TX C–

6	RX data–		RX B–

7	Not used		RX D+

8	Not used		RX D–

SFP Port Pinouts and Cable Specifications

For information about SFP modules supported by the Cisco ASR 901 router, including pinouts, see the Cisco Interfaces and Modules support section on Cisco.com.

Note Pins not listed in the tables in this appendix are not connected

T1/E1 Port Pinouts

Figure B-2shows the RJ-48C connector used by the T1/E1 ports on the TDM interface module on the Cisco ASR 901 router.

Figure B-2 RJ-48C Connector

87654321

RJ-48C connector

24939

Figure B-3shows the RJ-48C connector wiring for the T1/E1 cable.

Figure B-3 RJ-48-to-RJ-48 T1/E1 Cable Wiring

1

8

			H11419
			Cisco ASR 901 Series Aggregation Services Router Hardware Installation Guide


	B-2		OL-23778-01
	B-2		OL-23778-01

Image 56

Contents Americas Headquarters Text Part Number OL-23778-01Page N T E N T S Required Tools and Equipment Troubleshooting A-1 OL-23778-01 Document Revision History Revision Date Change SummaryObjectives AudienceOrganization ConventionsSafety Warnings Related DocumentationAbout This Guide Introduction Hardware DescriptionCisco ASR 901 Router Front View Cisco ASR 901 Router Ethernet Version Front View Cisco ASR 901 Router-Front ViewCisco ASR 901 Router Rear View Fan Grounding Point LugPower Supply Safety PrecautionsSpecification Value LEDsPin Connector a Pin Connector BEnvironmental Monitoring Temperature Sensor System SpecificationsDescription Specification Router Interface NumberingRegulatory Compliance Interface Number Location LabelSafety Guidelines Safety with EquipmentSafety with Electricity Preventing Electrostatic Discharge Damage Power Supply Considerations PrerequisitesSite Planning Site EnvironmentMethod of Procedure Air Flow GuidelinesUnpacking and Checking the Contents of your Shipment Required Tools and EquipmentInstallation Checklist Task Verified by DateConsole Port Considerations Creating a Site LogConsole Port Connections Task Verified byPreparing to Install the Router Console Port Considerations OL-23778-01 Installing the Cisco ASR 901 Mobile Wireless Router Network ModulesRack-Mounting Configuration Guidelines Mounting the Cisco ASR 901 RouterAttaching the Rack-Mounting Brackets Mounting the Cisco ASR 901 Router in a RackAttaching the Cable Guides Connecting the Chassis Ground and Power Grounding the Cisco ASR 901 RouterGrounding Point Power Connection Compliance Stripping a Ground WireWiring the DC-Input Power Source 6-Pin Terminal BlockInstalling and Removing SFP Modules Installing SFP ModulesInstalling an SFP Module into an SFP Module Slot Removing SFP ModulesConnecting Cables Connecting the Console PortTypes of RJ-45 Cables Console PortConnecting T1 and E1 Interface Cables Connecting the Network CablesConnecting Gigabit Ethernet Interface Cables Connecting GPS Cables Connecting SFP CablesConnecting Cables to the Bits Interface Powering On the Router Connecting to Alarm PortConnecting to the Management Ethernet Port Dressing Router CablesChecklist for Power Up Power-On ProcedureFormatting Procedures for Flash Memory Interpreting Front-Panel LEDsCopying Files File and Directory ProceduresDisplaying Contents of the Flash Memory Displaying File Content Deleting Files from the Flash MemoryWhat to Do After Installing the Hardware Enter a Directory and Determine the Current DirectoryOL-23778-01 Troubleshooting Problem SolvingSymptom Possible Cause Corrective Action Troubleshooting the Power and Cooling SystemsEnvironmental Reporting Features Troubleshooting Cables, and Connections Information Packet publicationReading the LEDs Chassis LEDsCopper GE from Quad combo PHY ports contain Two Leds each System LEDT1/E1 Interface LEDs SFP Ethernet Interface LEDsRJ-45 Ethernet Interface LEDs Color/State Description two LEDs for each T1/E1 portOL-23778-01 Cable Specifications Gigabit Ethernet Connector PinoutsT1/E1 Port Pinouts SFP Port Pinouts and Cable SpecificationsPin FE Signal GE Signal Pin Signal Name Direction Description Console Port Signals and PinoutsConsole Port Signals and Pinouts Pin Signal Name HP Pins Direction Description RJ-45-to-DB-9 Terminal Adapter ConsoleConsole RJ-45-to-DB-25 Port DTE Terminal Adapter Device Signal RJ-45 Pin DB-25 PinIdentifying a Rollover Cable GPS Port Pinouts Bits Port PinoutsTime of Day Pinouts Alarm Port Pinouts Pin Signal Name DescriptionManagement Ethernet Port Pinouts 10 MhzRxDP RxDN TxDP Not connected TxDN Site Log Date InitialsNumerics IN-2 IN-3 IN-4

Related manuals

Manual 884 pages 9.83 Kb