Grizzly G0486/G0487 owner manual Safety Instructions for Machinery

Page 10

SECTION 1: SAFETY

For Your Own Safety, Read Instruction Manual Before Operating this Machine

The purpose of safety symbols is to attract your attention to possible hazardous conditions. This manual uses a series of symbols and signal words which are intended to convey the level of importance of the safety messages. The progression of symbols is described below. Remember that safety messages by themselves do not eliminate danger and are not a substitute for proper accident prevention measures.

 

Indicates an imminently hazardous situation which, if not avoided,

 

 

WILL result in death or serious injury.

 

Indicates a potentially hazardous situation which, if not avoided,

 

COULD result in death or serious injury.

 

Indicates a potentially hazardous situation which, if not avoided,

 

MAY result in minor or moderate injury. It may also be used to alert

 

against unsafe practices.

NOTICE

This symbol is used to alert the user to useful information about

proper operation of the machine.

Safety Instructions for Machinery

1.READ THROUGH THE ENTIRE MANUAL BEFORE STARTING MACHINERY. Machinery presents serious injury hazards to untrained users.

2.ALWAYS USE ANSI APPROVED SAFETY GLASSES WHEN OPERATING MACHINERY. Everyday eyeglasses only have impact resistant lenses, they are NOT safety glasses.

3.ALWAYS WEAR A NIOSH APPROVED RESPIRATOR WHEN OPERATING MACHINERY THAT PRODUCES DUST. Wood dust is a carcinogen and can cause cancer and severe respiratory illnesses.

4.ALWAYS USE HEARING PROTECTION WHEN OPERATING MACHINERY. Machinery noise can cause permanent hearing damage.

5.WEAR PROPER APPAREL. DO NOT wear loose clothing, gloves, neckties, rings, or jewelry which may get caught in moving parts. Wear protective hair covering to con- tain long hair and wear non-slip footwear.

6.NEVER OPERATE MACHINERY WHEN TIRED, OR UNDER THE INFLUENCE OF DRUGS OR ALCOHOL. Be mentally alert at all times when running machinery.

-8-

G0486/G0487 Wide Belt Sander

Image 10
Contents DOUBLE-HEAD WIDE-BELT Sander Page Table of Contents Warranty & Returns Foreword IntroductionContact Info External Features Front View, Model G0487Internal Features Machine Data Sheet G0486 Machine Data Sheet G0487 Safety Safety Instructions for MachineryAlways Lock Mobile Bases if Used Before Operating Machinery Additional Safety for Wide Belt Sanders Grounding Circuit Requirements220V/440V Connection Amperage LoadsG0486 To wire the sander to440V Connection G0487Unpacking SET UPItems Needed for Set Up InventoryHardware Chart Clean Up Site ConsiderationsAir Line Installation Beginning AssemblyDust Collection To install the sanding belt Sanding BeltPressure Rollers Start Up Recommended Adjustments Choosing Sandpaper Operation SafetyOperations GritAdjusting Feed Rate Table MovementTypical amp draw meter Load chart Amp Draw MeterSanding Workpiece Platen Adjustment Three basic platen positionsAccessories H2845-Cleaning PadsGeneral MaintenanceSchedule Air System Sanding BeltsDust and Water Traps Platen Service ServiceTable Calibration To check the brake pads Brake ServiceTools Needed Qty To replace the brake padsTo check the sanding belt oscillation Oscillation TimingTo set the correct amount of airflow through G0486/G0487 Wide Belt Sander Oscillation Speed To adjust the oscillation speedTable Parallelism To adjust the pressure rollers To adjust the table parallelismPressure Rollers Belt Adjustment To adjust either V-beltConveyor Belt Replacement Conveyor belt removal sequence G0486/G0487 Wide Belt Sander Feed Belt Tension To adjust the feed belt tensionDo not remove the safety guard Feed Belt TrackingAir System Diagram Air system diagramTroubleshooting Motor & ElectricalRoller section, Control Panel Component Locations G0486/G0487 General Control Panel Electrical Diagram G0486/G0487 Wiring Box Electrical Diagram G0486 220V/440V, G0487 Wiring Box Components G0486 220V/440V, G0487 Wiring Box Electrical Diagram G0487 Wiring Box Components G0487 General Electric Diagram G0486/G0487 Motor Wiring G0486/G0487 Tool Box and Accessories Diagram Tool Box and Accessories Parts List DescriptionSanding Motor System Diagram Sanding Motor System Parts List DescriptionTable Lift System Diagram Table Lift System Parts List Conveyor System Diagram Conveyor System Parts List Roller Diagram Feed, Drum, and Pressure Roller Parts List Drum and Platen Sanding Drum and Platen Parts List Upper Roller System Diagram Upper Roller System Parts List Cabinet Assembly Diagram Cabinet Assembly Parts List DescriptionMain Electrical Panel and Controls Diagram Main Electrical Panel and Controls Parts List TransformerAir System Diagram Air System Parts List AIR Valve 1/4Machine Label Diagram Machine Label List Warranty & Returns Warranty Card CommentsGrizzly INDUSTRIAL, INC BOX BELLINGHAM, WA