Grizzly G0486/G0487 owner manual Oscillation Timing, To check the sanding belt oscillation

Page 31

Oscillation Timing

NOTICE

The oscillation adjustments have been per- formed at the factory and should require no further attention. However, we recommend verifying the settings.

When the oscillation is correctly adjusted, the sanding belt oscillates to the left and to the right at the same speed. If the sanding belt makes contact with a limit switch, as shown in Figure 26, the emergency braking system will activate and stop the sander immediately.

Limit

Switches

Sanding Belt

Sander Outline

(Top View)

Figure 26. Improper oscillation.

To check the sanding belt oscillation:

1.Be sure the sanding belt is properly installed and the belt tension knob and air supply are ON.

2.Turn ON the sanding belt.

—If the belt oscillates without contacting the limit switches, but the oscillation time to the left and right are NOT equal, proceed to Step 5, on Page 30.

—If the belt tracks away from the air fork and air jet, triggering into the limit switch, con- tinue with Step 3.

G0486/G0487 Wide Belt Sander

3.An adequate stream of air through the air fork gap (Figure 27) is essential for proper oscillation. If the jet of air is weak through the gap, the belt will track away from the controller and into the limit switch on the opposite end of the roller. The pivot action of the upper roller, and the resulting oscillation of the belt, are dependent upon adequate airflow through the air fork gap.

Oscillation Controller Gap

 

Air Fork and Air Jet

 

Figure 27. Oscillation components.

To set the correct amount of airflow through

the air fork gap:

1.

Remove the sanding belt then turn the belt

 

tension knob to the tensioned position.

2.

Loosen the lock nut on the airflow adjustment

 

knob (Figure 28).

3.

Turn the airflow adjustment knob (Figure 28)

 

clockwise until the airflow is completely OFF.

 

The upper roller should pivot to the right.

4.

Slowly turn the airflow adjustment knob

 

counterclockwise, and continue turning up

 

the air pressure until the roller pivots to the

 

left.

 

Lock Nut

Figure 28. Airflow adjustment knob.

-29-

Image 31
Contents DOUBLE-HEAD WIDE-BELT Sander Page Table of Contents Warranty & Returns Foreword IntroductionContact Info Front View, Model G0487 External FeaturesInternal Features Machine Data Sheet G0486 Machine Data Sheet G0487 Safety Instructions for Machinery SafetyAlways Lock Mobile Bases if Used Before Operating Machinery Additional Safety for Wide Belt Sanders Amperage Loads Circuit Requirements220V/440V Connection GroundingG0487 To wire the sander to440V Connection G0486Inventory SET UPItems Needed for Set Up UnpackingHardware Chart Site Considerations Clean UpAir Line Installation Beginning AssemblyDust Collection Sanding Belt To install the sanding beltPressure Rollers Start Up Recommended Adjustments Grit Operation SafetyOperations Choosing SandpaperTable Movement Adjusting Feed RateAmp Draw Meter Typical amp draw meter Load chartThree basic platen positions Sanding Workpiece Platen AdjustmentH2845-Cleaning Pads AccessoriesGeneral MaintenanceSchedule Air System Sanding BeltsDust and Water Traps Platen Service ServiceTable Calibration To replace the brake pads Brake ServiceTools Needed Qty To check the brake padsTo check the sanding belt oscillation Oscillation TimingTo set the correct amount of airflow through G0486/G0487 Wide Belt Sander Oscillation Speed To adjust the oscillation speedTable Parallelism To adjust the pressure rollers To adjust the table parallelismPressure Rollers To adjust either V-belt Belt AdjustmentConveyor Belt Replacement Conveyor belt removal sequence G0486/G0487 Wide Belt Sander Feed Belt Tracking To adjust the feed belt tensionDo not remove the safety guard Feed Belt TensionAir system diagram Air System DiagramMotor & Electrical TroubleshootingRoller section, Control Panel Component Locations G0486/G0487 General Control Panel Electrical Diagram G0486/G0487 Wiring Box Electrical Diagram G0486 220V/440V, G0487 Wiring Box Components G0486 220V/440V, G0487 Wiring Box Electrical Diagram G0487 Wiring Box Components G0487 General Electric Diagram G0486/G0487 Motor Wiring G0486/G0487 Tool Box and Accessories Diagram Description Tool Box and Accessories Parts ListSanding Motor System Diagram Description Sanding Motor System Parts ListTable Lift System Diagram Table Lift System Parts List Conveyor System Diagram Conveyor System Parts List Roller Diagram Feed, Drum, and Pressure Roller Parts List Drum and Platen Sanding Drum and Platen Parts List Upper Roller System Diagram Upper Roller System Parts List Cabinet Assembly Diagram Description Cabinet Assembly Parts ListMain Electrical Panel and Controls Diagram Transformer Main Electrical Panel and Controls Parts ListAir System Diagram AIR Valve 1/4 Air System Parts ListMachine Label Diagram Machine Label List Warranty & Returns Comments Warranty CardBOX BELLINGHAM, WA Grizzly INDUSTRIAL, INC