Schumacher SF-60, SF 1052 Personal Precautions and Safety, Ground and AC Power Cord Connections

Page 2

B.PERSONAL PRECAUTIONS AND SAFETY

1.WARNING: Wear complete eye protection and clothing protection, when working with lead-acid batteries.

2.Make sure someone is within range of your voice or close enough to come to your aid when you work with or near a lead-acid battery.

3.Have plenty of fresh water and soap nearby for use if battery acid contacts skin, clothing, or eyes. If battery acid contacts skin or clothing, wash immediately with soap and water.

4.Avoid touching your eyes while working with a battery. Acid particles (corrosion) may get into your eyes! If acid enters your eye, immediately flood eye with running cold water for at least 10 minutes. Get medical attention immediately.

5.Remove all personal metal items such as rings, bracelets,

necklaces, and watches when working with a lead-acid battery. A lead-acid battery can produce a short-circuit current high enough to weld a ring (or the like) to metal, causing a severe burn.

6.Take care not to drop a metal tool or other metal onto the battery. Metal may cause sparking or short circuit the battery or another electrical device. Sparking may cause an explosion.

7.Always operate battery charger in an open well ventilated area.

8.NEVER smoke or allow a spark or flame in the vicinity of the battery or engine. Batteries generate explosive gases!

C.GROUND AND AC POWER CORD CONNECTIONS

Charger should be grounded to reduce the risk of electric shock. Charger is equipped with an electric cord having an equipment ground- ing conductor and a grounding plug. The plug must be plugged into an outlet that is properly installed and grounded in accordance with all local codes and ordinances. This battery charger is designed for use on a nominal 120 volt circuit and has a grounded plug that looks like the plug illustrated in FIGURE 1 (A). This plug should be used in a grounded outlet. The plug pins must fit the receptacle (outlet).

ADAPTER: A temporary adapter, as shown in FIGURE 1 (B) and (C), may be used to connect the charger plug to a two pole receptacle (outlet), as shown in FIGURE 1 (B).

NOTE: The temporary adapter should be used only until a properly grounded outlet can be installed by a qualified electrician.

GROUNDING

SCREW

FIGURE 1 GROUNDING METHODS

DANGER: Never alter the AC cord or plug provided. If it will not fit outlet, have a proper outlet installed by a qualified electrician. Improper connection can

result in a risk of an electrical shock. DANGER: Before using an adapter, as illustrated, be certain that the center screw of the outlet plate is grounded. The green-colored rigid ear or lug extending from the adapter must be connected to a properly grounded outlet. Make certain it is grounded. If necessary, replace original outlet cover plate screw with a longer screw that will secure adapter ear or lug to outlet cover plate and make ground connection to grounded outlet.

USE OF ADAPTER PLUG NOT ALLOWED IN CANADA

D.

PREPARING TO CHARGE

 

 

1.Make sure that the voltage of the battery and the charger match. Select battery charger switch, if this model has one, accordingly.

2.Clean battery terminals. Take care to keep corrosion from coming in contact with your eyes.

3.If required, add distilled water in each cell until battery acid reaches levels specified by battery manufacturer. This helps purge exces- sive gas from cells. Do not overfill. For a battery without cell caps, carefully follow manufacturer’s recharging instructions.

4.Study all battery manufacturer’s specific precautions, such as re- moving or not removing cell caps while charging, and recommended rates of charge.

5.Be sure area around battery is well ventilated while battery is being charged. Gas can be forcefully blown away by using a piece of cardboard or other non-metallic material as a fan.

6.If necessary to remove battery from vehicle to charge, always remove grounded terminal from battery first. Make sure all accesso- ries in the vehicle are off, so as not to cause an arc.

7.A marine (boat) battery must be removed and charged on shore. To charge it on board requires equipment specially designed for marine

Charger Selection Guide (see section H)

Ampere

Charging

Recommended Battery

Rating

Hours

Uses

 

 

 

 

 

 

.3 amp

 

 

 

 

Maintain charge on battery.

1 amp

2-to Hrs.

Charge motorcycle, snow-

 

 

 

 

 

mobile, lawnmower, trickle

2 amp

3-6

Hrs.

charge car, truck, RV, marine.

6 amp

6-8

Hrs.

Charges car, truck, RV,

 

 

 

 

 

trolling outboard, tractor farm

10 amp

3-5

Hrs.

equip-ment.

30 amp

5 seconds on

Cranking assists helps turn

Boost

240 seconds off

engine when battery power

 

 

 

 

 

is low.

50 amp

2 minutes on

Boost battery for 2 minutes

Engine Start

5 minutes off

before Cranking Engine.

 

 

 

 

 

 

Sch555 English 10/30/97

2

Page 1 Page 3
Image 2
Page 1 Page 3
Contents Electric Corporation General Battery SafetyImportant Safety Instructions Length of cord feet 100 150 AWG size of cordPreparing to Charge Personal Precautions and SafetyGround and AC Power Cord Connections USE of Adapter Plug not Allowed in CanadaPositivenegative Battery Charger Power Operating Instruction Charging Battery in VehicleOperating Instruction Charging Battery OUT of Vehicle To Grounded Power OutletChecking the Vehicle Charging System Meter FunctionsPercent of Charge Switches Battery Charger ControlsBattery Types TimerCharger Location Precautions Battery ChargingIndications of a Fully Charged Battery Charge PeriodBusiness Center Drive Mount PROSPECT, IL Consignes DE Sécurité Générales SUR LES ChargeursLongueur de la rallonge pieds 100 150 Calibre des fils Préparatifs DE Charge Consignes DE Sécurité À Lintention DE LusagerRaccordement DU Cordon CA ET Mise À LA Terre ’UTILISATION DE L’ADAPTATEUR N’EST PAS Permise AU CanadaBorne Négative Mise À LA Masse Borne Positive Mise À LA MasseFoncitons DE Lampéremétre ET DU Voltmétre VoltmètreTypes DE Batterie Commandes DU Chargeur DE BatterieDisjoncteur InterrupteursPériode DE Charge Mise EN Garde SUR L’EMPLACEMENT DU ChargeurCharge DE LA Batterie Indications D’UNE Batterie Complètement Chargée

MCF-1, SF 1052, SF 1010-2, SF 1012D, SF 1250 specifications

Schumacher is a renowned brand within the automotive and power solutions industry, particularly known for their advanced battery chargers and jump starters. Among their product lineup, the Schumacher SF series stands out, featuring models such as the SF-60, SF 1250, SF 1012D, SF 1010-2, and SF 1052. Each model is designed to meet diverse charging needs while incorporating innovative technology and user-friendly features.

The Schumacher SF-60 is a versatile battery charger that supports a range of battery types including AGM, gel, and conventional lead-acid batteries. It features automatic voltage detection and a microprocessor-controlled system, which ensures optimal charging based on the battery’s condition. This model also boasts a built-in safety features including reverse polarity protection and overcharge protection, making it a reliable choice for both professional and personal use.

Moving to the SF 1250, this model further enhances the charging experience with a higher amperage output, allowing for faster charging times. It also includes an LCD display that provides real-time information on voltage, amperage, and charging status. The SF 1250's robust construction and advanced cooling system help prevent overheating, ensuring longevity and performance under various conditions.

The SF 1012D is another impressive model with dual charging options, enabling users to charge two batteries simultaneously. Its compact design does not compromise on functionality, coming equipped with smart charging technology that adapts based on battery type and condition. Moreover, the SF 1012D offers a user-friendly interface with LED indicators for easy operation and monitoring.

The SF 1010-2 model is designed for portability and convenience. Weighing less than most of its competitors, it features an ergonomic handle for easy transport. With a simple plug-and-play operation, even novice users can quickly connect and charge their batteries without technical know-how. This model also includes safety features such as thermal protection, making it a worry-free choice.

Lastly, the SF 1052 combines high performance with accessibility. It features a digital display that provides comprehensive feedback regarding the charging process. Its unique design accommodates a variety of battery types and sizes, making it ideal for everything from cars to motorcycles and even power sport vehicles. The integrated maintenance mode ensures that batteries remain in optimal condition, extending their lifespan.

In conclusion, the Schumacher SF series offers diverse models equipped with innovative features and technologies designed to meet various charging needs. From the compact and user-friendly SF 1010-2 to the robust SF 1250, each model provides reliability, safety, and efficiency, making Schumacher a trusted choice for battery solutions.
Top Page Image Contents