Bosch Power Tools 1634VS manual Maintenance, Accessories, Cleaning

Page 9

BM 2610910645 12/00 1/23/01 10:53 AM Page 9

Maintenance

Service

!WARNING Preventive maintenance performed by unauthorized

personnel may result in misplacing of internal wires and components which could cause serious hazard. We recommend that all tool service be performed by a Bosch Factory Service Center or Authorized Bosch Service Station.

TOOL LUBRICATION

Your Bosch tool has been properly lubricated and is ready to use. It is recommended that tools with gears be regreased with a special gear lubricant at every brush change.

CARBON BRUSHES

The brushes and commutator in your tool have been engineered for many hours of dependable service. To maintain peak efficiency of the motor, we recommend every two to six months the brushes be examined. Only genuine Bosch replacement brushes specially designed for your tool should be used.

BEARINGS

After about 300-400 hours of operation, or at every second brush change, the bearings

should be replaced at Bosch Factory Service Center or Authorized Bosch Service Station. Bearings which become noisy (due to heavy load or very abrasive material cut- ting) should be replaced at once to avoid overheating or motor failure.

Cleaning

!WARNING To avoid accidents always disconnect the tool from

the power supply before cleaning or performing any maintenance. The tool may be cleaned most effectively with compressed dry air. Always wear safety goggles when cleaning tools with compressed air.

Ventilation openings and switch levers must be kept clean and free of foreign matter. Do not attempt to clean by inserting pointed objects through openings.

!CAUTION Certain cleaning agents and solvents damage

plastic parts. Some of these are: gasoline, carbon tetrachloride, chlorinated cleaning solvents, ammonia and household detergents that contain ammonia.

Accessories

!WARNING If an extension cord is necessary, a cord with

adequate size conductors that is capable of carrying the current necessary for your tool must be used. This will prevent excessive voltage drop, loss of power or overheating. Grounded tools must use 3- wire extension cords that have 3-prong plugs and receptacles.

NOTE: The smaller the gauge number, the heavier the cord.

RECOMMENDED SIZES OF EXTENSION CORDS 120 VOLT ALTERNATING CURRENT TOOLS

Tool’s

Cord Size in A.W.G.

Wire Sizes in mm2

 

 

 

 

 

 

 

 

Ampere

 

 

 

 

 

 

 

 

Cord Length in Feet

Cord Length in Meters

Rating

 

25

50

100

150

15

30

60

120

3-6

 

 

 

 

 

 

 

 

18

16

16

14

.75

.75

1.5

2.5

6-8

18

16

14

12

.75

1.0

2.5

4.0

8-10

18

16

14

12

.75

1.0

2.5

4.0

10-12

16

16

14

12

1.0

2.5

4.0

12-16

14

12

 

 

 

 

 

 

 

 

 

*

Carrying case

(*= standard equipment)

*

Blades

(**= optional accessories)

 

 

** Standard blade clamp

-9-

Image 9
Contents Read Before Using Lire avant usage Leer antes de usar Electrical Safety Power Tool Safety RulesPersonal Safety Work AreaSafety Rules for Reciprocating Saws ServicePeriodic maintenance schedule for your tool BM 2610910645 12/00 1/23/01 1053 AM Symbols Functional Description and Specifications Reciprocating SawMeasures reduce the risk of starting the tool accidentally Assembly Operating InstructionsPreparing the Saw Using the SAW Sawing TipsPocket Cuts Maintenance AccessoriesCleaning Aire de travail Règles de Sécurité GénéralesSécurité électrique Sécurité des personnesRéparation Règles de sécurité concernant les scies va-et-vientLe plomb provenant des peintures à base de plomb Symboles Scies va-et-vient Description fonctionnelle et spécificationsAssemblage Consignes de fonctionnementApprêt de la scie Utilsation DE LA Scie Conseils PratiquesCoupes EN Guichet Accessoires EntretienNettoyage Area de trabajo Normas de seguridad para herramientas mecánicasSeguridad eléctrica Seguridad personalServicio Normas de seguridad para sierras alternativasBM 2610910645 12/00 1/23/01 1053 AM Símbolos Con aislamiento dobleDe Ni-Cd Descripción funcional y especificaciones Sierras alternativasRiesgo de arrancar la herramienta accidentalmente Ensamblaje Instrucciones de funcionamientoPreparacion de la sierra Utilización DE LA Sierra Consejos Para AserrarCortes DE Bolsillos Mantenimiento AccesoriosLimpieza BM 2610910645 12/00 1/23/01 1053 AM BM 2610910645 12/00 1/23/01 1053 AM Limited Warranty of Bosch Portable and Benchtop Power Tools