Coleman 024-0076CT warranty Air Motor Lubrication, Air motor

Page 21

USERUSER--MAINTENANCEMAINTENANCE INSTRUCTIONSINSTRUCTIONS

Air Motor Lubrication

To maintain the maximum performance of the air tool, it must be lubricated each time it is used. Dust, dirt, rust and oil residue will build up inside the tool and reduce the performance. An in-line oiler is recommended for proper auto- matic tool lubrication (see Figure 1). If an in-line oiler is not available, the tool can be lubricated manually through the inlet port (see Figure 3).

1.Disconnect the air tool from the air supply.

2.Turn the tool upside down and while depressing the trigger, add 4-6 drops of Coleman Powermate® air tool oil #018-0059SP or SAE10 nondetergent oil into the air inlet. NOTE: Depressing the trigger helps circulate oil in the

air motor.

Figure 3

 

3.Reconnect the tool to the air supply, cover the exhaust port end with a

towel and run in forward and reverse directions for approximately 30 seconds to remove excess oil.

NOTE: If the tool remains sluggish after it has been lubricated, the internal components may need to be cleaned.

To Clean:

Disconnect the air tool from the air supply and pour or spray a generous amount of WD-40® into the air inlet with the trigger depressed. Connect the tool to the air supply, cover the exhaust port end with a towel and run in forward and reverse directions for approximately 30 seconds. Follow the air motor lubrication instructions above after cleaning is completed to re-lubricate the tool.

After oiling or cleaning, cover the exhaust port with a towel and operate the tool for a few seconds to safely remove the excess oil. Clean the handle and surface of the tool of any oil residue. Failure to cover the exhaust port and clean the tool, can

result in serious injury. Note: Keep the towel away from moving parts!

TROUBLESHOOTINGG GUIDEGUIDE

SYMPTOM

POSSIBLE CAUSE(S)

CORRECTIVE ACTION

 

 

 

Tool will not run or runs

Grit in tool; tool gummed up

Clean the air motor inside the tool with WD-40®

slowly

 

(see “user maintenance” section).

 

No oil in tool

Add 4-6 drops of air tool oil into the air inlet of the

 

 

tool (see “user maintenance” section).

 

Low air pressure

Adjust compressor regulator to 90 PSI.

 

Air hose leaks

Tighten and seal hose fittings with Teflon® tape if

 

 

leaks are found.

 

 

 

 

TOOL SPECIFICATIONSTIONS

Maximum Torque

50 ft/lbs

Average SCFM Requirements

4.0 SCFM @ 90 PSI

Recommended Hose Size

3/8”

Air Inlet

1/4” NPT (female)

Square Drive

3/8”

Maximum Working Pressure

90 PSI

5 - ENG

Page 20 Page 22
Image 21
Page 20 Page 22
Contents 200-2368, Rev. a General Safety Safetysafety Guidelinesguidelines -- DefinitionsdefinitionsWork Area Safety Personal SafetyTool USE and Care Safety Tool Service SafetyAIR Source Safety Typicaltypical Instinstallaallationtion To begin using the toolOperaoperatingting Instructionsinstructions To Clean Symptom Possible Causes Corrective ActionAir Motor Lubrication Powermate Corporation Airport Road Box Kearney, NE Fax Limitedlimited WwarrantyarrantySécurité Générale Sécurité DE Laire DE TravailSécurité Personnelle Sécurité Relative À Lutilisation ET À Lentretien DE Loutil Sécurité Lors DE Lentretien DUN OutilSécurité DE LA Source Dalimentation EN AIR Instinstallaallationtion Typetype Modemode DemploidemploiAvant dutiliser loutil Lubrification du moteur pneumatique Entretienentretien Pparar LutilisalutilisateurteurDappuyer sur la détente Symptôme Causes Possibles Mesure CorrectiveGarantiegarantie Limitéelimitée Seguridad EN EL Lugar DE Trabajo Seguridad GeneralSeguridad Personal Asegúrese de que la toalla no esté cerca de partes moviblesSeguridad DE USO Y Cuidado DE LA Herramienta Seguridad DEL Servicio DE LA HerramientaSeguridad DEL Suministro DE Aire Instinstalaciónalación Típicatípica Instruccionesinstrucciones Dede OperaciónoperaciónPara comenzar a utilizar la herramienta Lubricación del motor de aire Motor de aireSíntomas Posibles Causas Medida Correctiva Garantíagarantía Limitlimitadaada 200-2370, Rev. a Safetysafety Guidelinesguidelines -- Definitionsdefinitions Tool USE and Care Safety Typicaltypical Instinstallaallationtion Air motor Limitedlimited Wwarrantyarranty Conservez CES Instructions Sécurité Relative À Lutilisation ET À Lentretien DE Loutil Instinstallaallationtion Typetype Couple maximum Lb-pi Exigences de pression moyenne Garantiegarantie Limitéelimitée Conserve Estas Instrucciones Seguridad DE USO Y Cuidado DE LA Herramienta Instinstalaciónalación Típicatípica Especificaciones DE LA Herramientherramientaa Garantíagarantía Limitlimitadaada

024-0076CT specifications

The Coleman 024-0076CT is a versatile and feature-rich camping lantern designed to meet the needs of outdoor enthusiasts. This innovative product combines functionality, durability, and user-friendly design, making it ideal for camping trips, emergency preparedness, and outdoor events.

One of the standout features of the Coleman 024-0076CT is its impressive illumination capability. With a maximum brightness of 1,000 lumens, this lantern ensures you have ample light for various activities, whether you're setting up camp, cooking, or simply enjoying a nighttime gathering. It offers multiple brightness settings, allowing users to customize the light intensity based on their needs, which helps to extend battery life while also providing the right amount of illumination.

Another key characteristic of the Coleman 024-0076CT is its power source. The lantern is designed to run on both rechargeable batteries and standard D-cell batteries, offering flexibility in how you power it. When using rechargeable batteries, you can easily keep the lantern charged for extended periods, making it a perfect companion for longer trips. The convenient USB port allows for easy charging, ensuring you never run out of power when you need it most.

Durability is another highlight of this Coleman lantern. Constructed with high-quality materials, it is built to withstand the rigors of outdoor use. The rugged design includes water resistance, providing peace of mind during unexpected weather changes. This feature ensures that the lantern remains operational even in wet conditions, making it a reliable option for various environments.

In addition to its lighting capabilities, the Coleman 024-0076CT also features a built-in handle for easy carrying and hanging. This thoughtful design element enhances portability, allowing users to conveniently transport the lantern to different locations or hang it in a tent or tree for ambient lighting.

Safety is also a priority. The lantern includes a cool-touch exterior, which prevents overheating and allows for safe handling even after extended use. This essential feature is particularly beneficial when children or pets are around, reducing the risk of burns or accidents.

In summary, the Coleman 024-0076CT is a powerful, flexible, and durable camping lantern that stands out in the outdoor lighting market. With its bright illumination, multiple power options, rugged construction, and user-friendly design, it is an excellent choice for campers, hikers, and anyone who values reliability in their outdoor gear. Whether for casual outdoor use or emergency situations, this lantern delivers performance and peace of mind.
Top Page Image Contents