SSI America 9200 user manual SSi requirement

Page 8

Model 9200 Programmable Dual-loop Controller

Electrical Installation

The Model 9200 requires 24VDC, 4 Watt, 60 Hz, single-phase power. A 24 VDC power supply is required and is generally included as part of the Model 9200 system. This power supply has a universal input that can accept between 60 and 265VAC. Power should be applied in accordance with the electrical drawings that have been supplied. Since each installation is unique for each site, the customer is responsible for providing adequate power and making it available to the Model 9200 power supply.

SSi requirement:

MOV’s must be wired across the isolation relay coil terminals on all isolation relays that are connected to solenoids. Further…. MOV’s must be connected across the HOT and NEUTRAL wires when the solenoid is

wired to them. IT IS AN ABSOLUTE MUST to have the MOV’s at BOTH LOCATIONS.

Instrument Start-up

On power-up, the Operator Interface will display a logo screen for thirty seconds and then switch to the default “Status” screen. The logo display can be terminated early by touching the screen.

Flash Card & Flash Card Reader

!Never remove the flash card when the Operator Interface is “ON”.

To properly shut down the Operator Interface, press the “Menu” button, and select “Shutdown”. At the prompt, press “yes” to shut down the operator interface. This will bring you to a conventional Microsoft Windows screen. Sliding the black switch to the “OFF” position (located directly over the green power connector, on the back of the Operator Interface) will turn off the power to the operator interface.

Once the Operator Interface is turned off, remove the compact flash card cover at the top of the display unit, exposing the card. Press the black release button and the card will pop out of the slot. To replace the flash card simply return the card to the slot, making sure that the release button is in it’s “UP” position, and replace the flash card cover to it’s proper position. To restore power to the unit, move the black switch to the right or “ON” position.

Operator Interface Screen Saver

The operator interface has a default screen saver. It automatically “blanks” the screen after ten (10) minutes of non-activity. To dis-engage the screen saver simply touch the screen and it will re-appear.

SSi Manual SERIES 9200

8

Programmable Dual-loop

Page 7 Page 9
Image 8
Page 7 Page 9
Contents Model 9200 Controller Model 9200 Programmable Dual-loop Controller Model 9200 Programmable Dual-loop Controller Model 9200 Programmable Dual-loop Controller 24VDC / 1 AMP Ohms Total IP10 hand protected Model 9200 Terminals Connections Model 9200 Programmable Dual-loop Controller SSi requirement Installation Model 9200 Programmable Dual-loop Controller Model 9200 Programmable Dual-loop Controller Model 9200 Programmable Dual-loop Controller Model 9200 Programmable Dual-loop Controller Model 9200 Programmable Dual-loop Controller Model 9200 Programmable Dual-loop Controller Model 9200 Programmable Dual-loop Controller Model 9200 Programmable Dual-loop Controller Model 9200 Programmable Dual-loop Controller Model 9200 Programmable Dual-loop Controller Configuration Model 9200 Programmable Dual-loop Controller Model 9200 Programmable Dual-loop Controller Model 9200 Programmable Dual-loop Controller Model 9200 Programmable Dual-loop Controller Model 9200 Programmable Dual-loop Controller Model 9200 Programmable Dual-loop Controller Model 9200 Programmable Dual-loop Controller Adam VC Base Aipc Model 9200 Programmable Dual-loop Controller Step Opcode Temperature Atmosphere Option Model 9200 Programmable Dual-loop Controller Model 9200 Programmable Dual-loop Controller Model 9200 Programmable Dual-loop Controller Model 9200 Programmable Dual-loop Controller Model 9200 Programmable Dual-loop Controller Model 9200 Programmable Dual-loop Controller Model 9200 Programmable Dual-loop Controller Model 9200 Programmable Dual-loop Controller Model 9200 Programmable Dual-loop Controller Model 9200 Programmable Dual-loop Controller Model 9200 Programmable Dual-loop Controller Model 9200 Programmable Dual-loop Controller Calibrate Span input 1 range Span input 2 range Zero input 3 range Zero Output Span Output Enter measured output current mA Supervisor Model 9200 Programmable Dual-loop Controller Model 9200 Programmable Dual-loop Controller Model 9200 Programmable Dual-loop Controller Model 9200 Programmable Dual-loop Controller Programs Parameter Value Series 9200 Opcodes Model 9200 Programmable Dual-loop Controller Model 9200 Programmable Dual-loop Controller Model 9200 Programmable Dual-loop Controller Model 9200 Programmable Dual-loop Controller Applications Information Series 9200 Factory defaults August 17 Rev August 6 Model 9200 Programmable Dual-loop Controller Model 9200 Programmable Dual-loop Controller OPT Code Temp SET PT Rev Description Date
Top Page Image Contents