HP Tape manual Secure the drive

Page 34

 

For further

 

details, see:

Before you start

 

Check system prerequisites. (Always connect to a wide, Ultra SCSI-2 Low Voltage Differential (LVD)

page 3

or Single-Ended (SE) SCSI bus.) Visit the HP Surestore DLT1 web page: //www.hp.com/

 

support/dlt1. For example, you can use HP Library & Tape Tools to help you install your drive.

 

Step 1: Check the drive’s SCSI ID

 

Check the tape drive’s SCSI ID. If necessary, change it from the default of 5 by resetting the jumpers

page 7

on the back of the drive.

 

Step 2: Prepare the mounting bay

 

Switch off the computer and attached devices, remove all power cables, and remove the

page 9

computer’s outer casing. Remove the blanking plate(s) from a spare, full-height 5-¼ inch bay.

 

Step 3: Attach mounting hardware

 

If your computer requires special rails to install the tape drive, mount them on the drive now. In the

page 11

box, you will find a mounting tray for HP NetServer L-series.

 

Step 4: Install the drive

 

Install the drive. To make it easier to fit the cables, do not secure the drive with screws yet.

page 13

Step 5: Attach power and SCSI cables

 

Attach a spare power cable from the computer’s internal power supply. Attach a SCSI cable to the

page 15

drive and to the computer’s SCSI host adapter (which should be LVD or SE).

 

Step 6: Secure the drive

 

Secure the drive into place with screws. Replace the computer’s outer casing.

page 17

Your tape drive

 

Find out what the LEDs on your tape drive indicate and make sure you are using the correct type

page 19

of cartridge.

 

Use the correct media

 

Find out how to use and care for DLTtape IV cartridges and how to use DLT1 cleaning cartridges.

page 21

Operating the tape drive

 

Power on the system and check the tape drive is operational. Carry out a trial backup and restore.

page 23

HP Library & Tape Tools

 

Find out more about the free diagnostic and troubleshooting tool supplied with your tape drive.

page 25

Register your tape drive

 

Register your tape drive to ensure you receive up-to-date information about HP’s products, services

page 26

and support.

 

Troubleshooting

 

If you experience problems during installation, check this section first. For more detailed

page 27

troubleshooting information visit the web site: //www.hp.com/support/dlt1.

 

1

Image 34
Contents Date CopyrightRevision history OctoberObtaining technical support North and south america Europe, middle east and africa Asia pacific Warranty WarrantyWarranty conditions ExclusionsCustomer service form Before you start Resetting the drive Switching on the driveIf you have problems during self test OperationWrite Protected first light Front panel lightsFront panel lights Ready second lightTo unload a cartridge Loading and unloadingTo load a cartridge To label a cartridgeCartridge care Cleaning cartridge CleaningCleaning strategy Cleaning the tape heads on a driveFeatures and specifications Choose your model from the bulleted list belowHp surestore dlt1i Non-operating limits storage ranges Hp surestore dlt1eDlt1e Action Drive Media compatibilityDLT1 compatibility matrix DLT4000 DLT7000Diagnostics Troubleshooting Frequently asked questions FAQsScsi configuration This topic is available in English only ModelCreating the device files HP-UX systems series 700 onlyDetermining the Scsi id ExampleConfiguring for Digital Unix DEC systems, Digital UnixIBM RS/600 systems, AIX Configuring the device filesScsi configuration Unix configuration hp systems Device file names under AIXPC-based UNIX, SCO and Linux Silicon Graphics systems, Irix Mtcan and constants valuesFor all adapters Sun systems, Solaris 2 SunOSHp-data values Value MeaningOverview Verify the installationVerifying the installation System-specific argumentsGlossary Rail kits Ordering suppliesAdapters MediaOrdering supplies DLT1 Secure the drive Scsi ID Mounting bay Scsi host bus adapterScsi ribbon cable Mounting hardwareBackup software User documentation HP product registrationDrivers HP Library & Tape ToolsChecking the drive’s Scsi ID Page Preparing mounting bay in a Page Attaching tray for NetServer L-Series servers Page Installing the drive Page Attaching Scsi and power cables to internal drive Page Securing the drive side mounting screws shown Page Tape drive controls and indicators Front panel LEDs ReadyWrite protecting cartridges Write-protecting cartridges Cleaning cartridgesLooking after cartridges Loading a cartridge To load a cartridge Check operationTo unload a cartridge Using HP Library & Tape Tools Page If you have Internet access, register electronically If you do not have internet accessNone of the drive’s LEDs illuminate Other sources of information Page External tape drive Check the drive’s Scsi ID Connect the power cableTroubleshooting Connect the Scsi cableScsi ID Scsi cable Backup software HP product registration Checking the Scsi ID Page Connecting the Scsi cable Page Connecting the power cable Page Tape drive front panel Front panel LEDs Write-protecting cartridges Write-protecting cartridges Loading a DLTtape cartridge Check operation Using HP Library & Tape Tools Page If you have internet access, register electronically None of the drive’s LEDs illuminate All of the LEDs on the front panel blink continuallyIs properly terminated