HP Accessory 651176-002 manual Installation

Page 22

WARNING: To meet the requirements stated in NEC (NFPA 70) Articles 645-10 and 645-11, a UPS installed in a computer equipment room must be connected to a REPO circuit.

IMPORTANT: The remote switch must be in the Off (open) position to enable power to the output receptacles.

NOTE: Wire the connector block using stranded, nonshielded wire (AWG #22 - #18, or equivalent).

Separate wire pairs are attached to a single, normally-open contact in a parallel connection. HP recommends using different colors for the positive and negative wires.

If a connector becomes disconnected and is reconnected with reversed polarity, a REPO is initiated. To avoid REPO port disconnect:

•Minimize wire strain while connecting the REPO port.

Installation 22

Image 22

Contents HP R/T3000 G2 UPS User Guide Page Contents Power management Spares Acronyms and abbreviations Documentation feedback Index UPS R/T3000 G2 overview Component identificationUPS front panel UPS front panel LED indicators UPS front panel controlsHP UPS R/T3000 models T3000 NA and R/T3000j JPN rear panelT3000h NA and R/T3000h JPN rear panel T3000 INT rear panel Repo portERM rear panel Preparing to install the hardware InstallationPrecautions Tools and materialsSelecting a site Installing the mounting railsReadying the equipment Installation Installation Installing the UPS in a rack Connecting the battery leads Installation Attaching the UPS front bezel Connecting the host computer Connecting the Repo port Connecting the serial communications portInstallation Connecting the ground bonding cable Connecting the UPS to utility power Connecting devices to the UPSInstallation Installing the ERM in a rack Starting power to the loadConnecting the battery leads Attaching the ERM front bezel Connecting the ERM to the UPS Installation Installing the optional UPS Network Module Installing the UPS as a tower Connecting the UPS Network ModuleConnecting the battery leads Rotating the logo badge Continuing the installation Installing the ERM as a tower Installation Continuing the ERM installation Installing the extension bars if included Connecting and securing the power cords UPS operations Standby modeOperate mode Modes of operationAuto-Bypass mode Configure modeBattery mode Operating the UPS front panel controlsConfiguring the UPS Initiating a self-test Powering down the UPS Silencing an audible alarmVerifying the Repo port connection Maintenance Battery care and storage guidelines Important battery safety informationDetermining when to replace batteries UPS battery replacement procedure Obtaining new batteriesTesting the new battery module Replacing the ERM Replacing the UPSReplacing the UPS option card Configuring a USB to serial converter Updating the UPS firmwareReassigning the USB COM ports Maintenance Power management Power Protector softwarePower management Troubleshooting LED troubleshootingUPS is in Auto-Bypass mode UPS is in Converter Off mode General alarm conditionBypass is out of range Battery conditionUPS is on battery Input voltage is out of rangeSite wiring condition Overtemperature conditionInternal UPS fault condition Repo conditionUPS does not provide the expected backup time Checksum failure errorLow battery shutdowns UPS frequently switches between utility and battery powerERM physical specifications SpecificationsUPS physical specifications UPS input specificationsOutput tolerance specifications Battery specificationsPower protection specifications Output feature specificationsEnvironmental specifications High-voltage UPS battery runtimesLow-voltage UPS battery runtimes Repo port specificationsSpares UPS spare parts listOrdering spares ERM spare parts list Hardware optionsBefore you contact HP Support and other resourcesHP contact information $250,000 Computer Load Protection Guarantee Warranty informationLimited warranty Pre-Failure Battery WarrantyRecommended duration of use Regulatory compliance identification numbers Regulatory compliance noticesFederal Communications Commission notice Cables ModificationsCanadian notice Avis Canadien European Union regulatory notice Japanese notice Bsmi notice Korean notice Taiwan battery recycling notice Battery replacement noticeChinese notice Power cord statement for Japan Preventing electrostatic discharge Electrostatic dischargeGrounding methods to prevent electrostatic discharge Acronyms and abbreviations Documentation feedback Index On button, location UPS is on battery