HP Accessory 651176-002 manual European Union regulatory notice

Page 71

This Class A digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.

Cet appareil numérique de la classe A respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada.

Class B equipment

This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.

Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada.

European Union regulatory notice

Products bearing the CE marking comply with the following EU Directives:

Low Voltage Directive 2006/95/EC

EMC Directive 2004/108/EC

Ecodesign Directive 2009/125/EC, where applicable

CE compliance of this product is valid if powered with the correct CE-marked AC adapter provided by HP.

Compliance with these directives implies conformity to applicable harmonized European standards (European Norms) that are listed in the EU Declaration of Conformity issued by HP for this product or product family and available (in English only) either within the product documentation or at the following HP website (http://www.hp.eu/certificates) (type the product number in the search field).

The compliance is indicated by one of the following conformity markings placed on the product:

For non-telecommunications products and for EU harmonized telecommunications products, such as Bluetooth® within power class below 10mW.

For EU non-harmonized telecommunications products (If applicable, a 4-digit notified body number is inserted between CE and !).

Please refer to the regulatory label provided on the product.

The point of contact for regulatory matters is Hewlett-Packard GmbH, Dept./MS: HQ-TRE, Herrenberger Strasse 140, 71034 Boeblingen, GERMANY.

Disposal of waste equipment by users in private households in the European Union

Regulatory compliance notices 71

Image 71
Contents HP R/T3000 G2 UPS User Guide Page Contents Power management Spares Acronyms and abbreviations Documentation feedback Index UPS front panel Component identificationUPS R/T3000 G2 overview UPS front panel controls UPS front panel LED indicatorsT3000 NA and R/T3000j JPN rear panel HP UPS R/T3000 modelsT3000h NA and R/T3000h JPN rear panel Repo port T3000 INT rear panelERM rear panel Tools and materials InstallationPrecautions Preparing to install the hardwareReadying the equipment Installing the mounting railsSelecting a site Installation Installation Installing the UPS in a rack Connecting the battery leads Installation Attaching the UPS front bezel Connecting the host computer Connecting the serial communications port Connecting the Repo portInstallation Connecting the ground bonding cable Connecting devices to the UPS Connecting the UPS to utility powerInstallation Starting power to the load Installing the ERM in a rackConnecting the battery leads Attaching the ERM front bezel Connecting the ERM to the UPS Installation Installing the optional UPS Network Module Connecting the UPS Network Module Installing the UPS as a towerConnecting the battery leads Rotating the logo badge Continuing the installation Installing the ERM as a tower Installation Continuing the ERM installation Installing the extension bars if included Connecting and securing the power cords Modes of operation Standby modeOperate mode UPS operationsOperating the UPS front panel controls Configure modeBattery mode Auto-Bypass modeConfiguring the UPS Initiating a self-test Verifying the Repo port connection Silencing an audible alarmPowering down the UPS Maintenance Determining when to replace batteries Important battery safety informationBattery care and storage guidelines Obtaining new batteries UPS battery replacement procedureTesting the new battery module Replacing the UPS option card Replacing the UPSReplacing the ERM Updating the UPS firmware Configuring a USB to serial converterReassigning the USB COM ports Maintenance Power Protector software Power managementPower management LED troubleshooting TroubleshootingUPS is in Auto-Bypass mode General alarm condition UPS is in Converter Off modeInput voltage is out of range Battery conditionUPS is on battery Bypass is out of rangeRepo condition Overtemperature conditionInternal UPS fault condition Site wiring conditionUPS frequently switches between utility and battery power Checksum failure errorLow battery shutdowns UPS does not provide the expected backup timeUPS input specifications SpecificationsUPS physical specifications ERM physical specificationsOutput feature specifications Battery specificationsPower protection specifications Output tolerance specificationsRepo port specifications High-voltage UPS battery runtimesLow-voltage UPS battery runtimes Environmental specificationsOrdering spares UPS spare parts listSpares Hardware options ERM spare parts listHP contact information Support and other resourcesBefore you contact HP Pre-Failure Battery Warranty Warranty informationLimited warranty $250,000 Computer Load Protection GuaranteeRecommended duration of use Federal Communications Commission notice Regulatory compliance noticesRegulatory compliance identification numbers Canadian notice Avis Canadien ModificationsCables European Union regulatory notice Japanese notice Bsmi notice Korean notice Chinese notice Battery replacement noticeTaiwan battery recycling notice Power cord statement for Japan Grounding methods to prevent electrostatic discharge Electrostatic dischargePreventing electrostatic discharge Acronyms and abbreviations Documentation feedback Index On button, location UPS is on battery