HP Accessory 651176-002 manual On button, location

Page 79

HP technical support 66

I

input specifications 61

input voltage is out of range 58 installation instructions 13, 17, 26, 32, 35

installing the ERM	26, 35
installing the UPS	17, 32

internal UPS fault condition 59

J

Japanese notice 72

K

Korean notices 72

L

LEDs, testing 43

LEDs, troubleshooting 55 limited warranty 67

load protection guarantee 67 low battery shutdowns 60

M

maintenance 45

modes of operation 40, 57 modifications, FCC notice 70

N

nominal voltage, configuring 42

O

obtaining new batteries		47
On Battery LED, location		8
On Battery LED, troubleshooting				55
On button, location 8
On Bypass LED, troubleshooting				55
Operate mode	40
operating front panel controls			41
operations, UPS	40
optional items	65
ordering spares	64
output feature specifications			62
output specifications 61
output tolerance specifications				62
overload condition 59
Overload LED, location		8

Overload LED, troubleshooting 55 Overtemperature LED, location 8 Overtemperature LED, troubleshooting 55 overview, REPO port 11

P

phone numbers 66 physical specifications 61 power cord 74

power management 53

power protection specifications 62 powering down 44 preparation procedures 13

R

R/T3000 ERM 12 R/T3000 models 9 rack-to-tower conversion 32, 35 rear panel connectors 12 recommended duration of use 68

regulatory compliance identification numbers 69

regulatory compliance notices			69, 71, 73
replacing the batteries		45, 47
replacing the ERM	49
replacing the UPS	49
REPO condition 59
REPO port, overview		11
REPO port, specifications 63
REPO port, verifying connection			44
required information		66
required tools 13
Reset button, location		8
runtime specifications		63

S

safety considerations 13, 46 selecting a site 14

series number 69 site requirements 14 site wiring condition 59

Site Wiring Fault LED, location 8

Site Wiring Fault LED, troubleshooting 55 spares 64

specifications 61 Standby mode 40 static electricity 75 storing batteries 46 support 66 supported hardware 65

Index 79

Image 79

Contents HP R/T3000 G2 UPS User Guide Page Contents Power management Spares Acronyms and abbreviations Documentation feedback Index UPS R/T3000 G2 overview Component identificationUPS front panel UPS front panel controls UPS front panel LED indicatorsT3000 NA and R/T3000j JPN rear panel HP UPS R/T3000 modelsT3000h NA and R/T3000h JPN rear panel Repo port T3000 INT rear panelERM rear panel Tools and materials InstallationPrecautions Preparing to install the hardwareSelecting a site Installing the mounting railsReadying the equipment Installation Installation Installing the UPS in a rack Connecting the battery leads Installation Attaching the UPS front bezel Connecting the host computer Connecting the serial communications port Connecting the Repo portInstallation Connecting the ground bonding cable Connecting devices to the UPS Connecting the UPS to utility powerInstallation Starting power to the load Installing the ERM in a rackConnecting the battery leads Attaching the ERM front bezel Connecting the ERM to the UPS Installation Installing the optional UPS Network Module Connecting the UPS Network Module Installing the UPS as a towerConnecting the battery leads Rotating the logo badge Continuing the installation Installing the ERM as a tower Installation Continuing the ERM installation Installing the extension bars if included Connecting and securing the power cords Modes of operation Standby modeOperate mode UPS operationsOperating the UPS front panel controls Configure modeBattery mode Auto-Bypass modeConfiguring the UPS Initiating a self-test Powering down the UPS Silencing an audible alarmVerifying the Repo port connection Maintenance Battery care and storage guidelines Important battery safety informationDetermining when to replace batteries Obtaining new batteries UPS battery replacement procedureTesting the new battery module Replacing the ERM Replacing the UPSReplacing the UPS option card Updating the UPS firmware Configuring a USB to serial converterReassigning the USB COM ports Maintenance Power Protector software Power managementPower management LED troubleshooting TroubleshootingUPS is in Auto-Bypass mode General alarm condition UPS is in Converter Off modeInput voltage is out of range Battery conditionUPS is on battery Bypass is out of rangeRepo condition Overtemperature conditionInternal UPS fault condition Site wiring conditionUPS frequently switches between utility and battery power Checksum failure errorLow battery shutdowns UPS does not provide the expected backup timeUPS input specifications SpecificationsUPS physical specifications ERM physical specificationsOutput feature specifications Battery specificationsPower protection specifications Output tolerance specificationsRepo port specifications High-voltage UPS battery runtimesLow-voltage UPS battery runtimes Environmental specificationsSpares UPS spare parts listOrdering spares Hardware options ERM spare parts listBefore you contact HP Support and other resourcesHP contact information Pre-Failure Battery Warranty Warranty informationLimited warranty $250,000 Computer Load Protection GuaranteeRecommended duration of use Regulatory compliance identification numbers Regulatory compliance noticesFederal Communications Commission notice Cables ModificationsCanadian notice Avis Canadien European Union regulatory notice Japanese notice Bsmi notice Korean notice Taiwan battery recycling notice Battery replacement noticeChinese notice Power cord statement for Japan Preventing electrostatic discharge Electrostatic dischargeGrounding methods to prevent electrostatic discharge Acronyms and abbreviations Documentation feedback Index On button, location UPS is on battery