HP XU103UT manual Using Advanced System Diagnostics

Page 79

NOTE: If you connect your computer to a network, consult the network administrator before installing any software updates, especially system BIOS updates.

BIOS installation procedures vary. Follow any instructions that are displayed on the screen after the download is complete. If no instructions are displayed, follow these steps:

1.Open Windows Explorer by selecting Start > Computer.

2.Double-click your hard drive designation. The hard drive designation is typically Local Disk (C:).

3.Using the hard drive path you recorded earlier, open the folder on your hard drive that contains the update.

4.Double-click the file that has an .exe extension (for example, filename.exe). The BIOS installation begins.

5.Complete the installation by following the on-screen instructions.

NOTE: After a message on the screen reports a successful installation, you can delete the downloaded file from your hard drive.

Using Advanced System Diagnostics

Advanced System Diagnostics allows you to run diagnostic tests to determine if the computer hardware is functioning properly. The following diagnostic tests are available in Advanced System Diagnostics:

●Start-up test—This test analyzes the main computer components that are required to start the computer.

●Run-in test—This test repeats the start-up test and checks for intermittent problems that the start-up test does not detect.

●Hard disk test—This test analyzes the physical condition of the hard drive, and then checks all data in every sector of the hard drive. If the test detects a damaged sector, it attempts to move the data to a good sector.

●Memory test—This test analyzes the physical condition of the memory modules. If it reports an error, replace the memory modules immediately.

●Battery test—This test analyzes the condition of the battery and calibrates the battery if necessary. If the battery fails the test, contact HP Customer Support to report the issue and purchase a replacement battery.

●System Tune-Up—This group of additional tests checks your computer to make sure that the main components are functioning correctly. System Tune-Up runs longer and more comprehensive tests on memory modules, hard drive SMART attributes, the hard drive surface, the battery (and battery calibration), video memory, and the WLAN module status.

You can view system information and error logs in the Advanced System Diagnostics window.

Using Advanced System Diagnostics 69

Page 78 Page 80
Image 79
Page 78 Page 80
Contents HP Notebook Product notice Safety warning notice Iv Safety warning notice Table of contents VGA Hdmi External cards and devices Security Computer Setup Bios and Advanced System Diagnostics Appendix C Electrostatic discharge Index Finding more information about your new computer IntroductionSelect Start All Programs HP HP Documentation Windows Creating a wireless connectionIdentifying wireless and network status icons Networking select models onlyWindows Vista Select Start All Programs HP HP Connection Manager Turning wireless devices on or offUsing HP Connection Manager select models only Using operating system controlsConnecting to an existing Wlan Using a WlanSelect Start Connect to Protecting your Wlan Setting up a new WlanRoaming to another network Using HP Mobile Broadband select models onlyRemoving a SIM Inserting a SIMBluetooth and Internet Connection Sharing ICS Using GPS select models onlyUsing Bluetooth wireless devices Connecting to a wired networkConnecting a modem cable Selecting a location setting Connecting a country- or region-specific modem cable adapterWindows Select Start Devices and Printers Adding new locations when travelingConnecting to a local area network LAN select models only Page Multimedia Using the media activity controlsAudio Select Start Control Panel Hardware and Sound Sound Adjusting the volumeSelect Start All Programs Accessories Sound Recorder Checking audio functions on the computerVideo Webcam select models onlyPage Hdmi Intel Wireless Display select models only Configuring audio for HdmiShutting down the computer Power managementWindows 7-SelectStart Shut down Using power-saving states Setting power optionsInitiating and exiting Sleep Initiating and exiting Hibernation Using the power meterUsing power plans Viewing the current power planCustomizing power plans Selecting a different power planSetting password protection on wakeup Select Start All Programs HP HP Power Assistant Using HP Power Assistant select models onlyUsing battery power Finding additional battery informationManaging low battery levels Using Battery CheckDisplaying the remaining battery charge Maximizing battery discharge timeResolving a low battery level Conserving battery powerReplacing the battery Using external AC powerStoring a battery Disposing of a used batteryTesting an AC adapter Using switchable graphics select models only Switchable graphics/dual graphics select models onlyUsing dual graphics select models only External cards and devices Using Media Card Reader cards select models onlyInserting a digital card Configuring an ExpressCard Using ExpressCards select models onlyRemoving a digital card Inserting an ExpressCard Removing an ExpressCard Using smart cards select models onlyInserting a smart card Using a USB deviceRemoving a smart card Connecting a USB device Using 1394 devices select models onlyRemoving a USB device Connecting a 1394 device Using an eSATA device select models onlyRemoving a 1394 device Removing an eSATA device Connecting an eSATA deviceUsing optional external devices Using a serial device select models onlyUsing optional external drives Using the expansion port select models only Using the docking connector select models only Handling drives DrivesImproving hard drive performance Using hard drivesUsing Disk Defragmenter Using Disk CleanupManaging power with a parked hard drive Using HP 3D DriveGuard select models onlyIdentifying HP 3D DriveGuard status Inserting an optical disc Using optical drives select models onlyIdentifying the installed optical drive Using HP 3D DriveGuard softwareSlot-load Removing an optical discWhen the disc tray opens normally Slot-load Sharing optical drives Using RAID select models onlyProtecting the computer SecurityUsing passwords Password Function Setting passwords in WindowsChanging a Bios administrator password Setting passwords in Computer SetupManaging a Bios administrator password Setting a new Bios administrator passwordEntering a Bios administrator password Managing a Computer Setup DriveLock passwordDeleting a Bios administrator password Setting a DriveLock password Changing a DriveLock password Entering a DriveLock passwordRemoving DriveLock protection Entering an Automatic DriveLock password Using Computer Setup Automatic DriveLockRemoving Automatic DriveLock protection Using firewall software Using antivirus softwareInstalling critical security updates Installing an optional security cable Using HP ProtectTools Security Manager select models onlyLocating the fingerprint reader Using the fingerprint reader select models onlyCleaning procedures MaintenanceCleaning your computer Cleaning productsCleaning the TouchPad and keyboard Cleaning the sides and coverUpdating programs and drivers Using SoftPaq Download Manager Navigating and selecting in Computer Setup Computer Setup Bios and Advanced System DiagnosticsUsing Computer Setup Starting Computer SetupRestoring factory settings in Computer Setup Select Start Help and Support Maintain Updating the BiosDetermining the Bios version Downloading a Bios updateUsing Advanced System Diagnostics Page About the boot device order MultiBootConsidering boot order changes Enabling boot devices in Computer SetupSetting a new boot order in Computer Setup Choosing MultiBoot preferencesSetting a MultiBoot Express prompt Dynamically choosing a boot device using the f9 promptEntering MultiBoot Express preferences Configuring and deploying a software image Using Client Management SolutionsComputer Management HP Client Manager for Altiris select models only Managing and updating softwareHP SSM System Software Manager HP CCM Client Configuration Manager select models onlyIntel ME Configuration Using Intel Active Management Technology select models onlyEnabling the iAMT solution Using the MEBx setup utility menusChange Intel ME Password IAMT ConfigurationTraveling with the computer Page Troubleshooting resources Electrostatic discharge Index Symbols/NumericsKeys SIM
Top Page Image Contents