HP XU103UT Using 1394 devices select models only, Connecting a USB device, Removing a USB device

Page 48

Connecting a USB device

CAUTION: To reduce the risk of damage to a USB connector, use minimal force to connect the device.

▲Connect the USB cable for the device to the USB port.

NOTE: The following illustration may look slightly different than your computer.

You will hear a sound when the device has been detected.

NOTE: The first time you connect a USB device, a message in the notification area lets you know that the device is recognized by the computer.

Removing a USB device

CAUTION: To reduce the risk of damage to a USB connector, do not pull on the cable to remove the USB device.

CAUTION: To reduce the risk of loss of information or an unresponsive system, use the following procedure to safely remove the USB device.

1.To remove a USB device, save your information and close all programs associated with the device.

2.Click the remove hardware icon in the notification area, at the far right of the taskbar, and then follow the on-screen instructions.

3.Remove the device.

Using 1394 devices (select models only)

IEEE 1394 is a hardware interface that connects a high-speed multimedia or data storage device to the computer. Scanners, digital cameras, and digital camcorders often require a 1394 connection.

Some 1394 devices may require additional support software, which is usually included with the device. For more information about device-specific software, refer to the manufacturer's instructions.

The 1394 port also supports IEEE 1394a devices.

38 Chapter 5 External cards and devices

Image 48

Contents HP Notebook Product notice Safety warning notice Iv Safety warning notice Table of contents VGA Hdmi External cards and devices Security Computer Setup Bios and Advanced System Diagnostics Appendix C Electrostatic discharge Index Introduction Finding more information about your new computerSelect Start All Programs HP HP Documentation Creating a wireless connection Identifying wireless and network status iconsNetworking select models only WindowsWindows Vista Turning wireless devices on or off Using HP Connection Manager select models onlyUsing operating system controls Select Start All Programs HP HP Connection ManagerUsing a Wlan Connecting to an existing WlanSelect Start Connect to Setting up a new Wlan Protecting your WlanUsing HP Mobile Broadband select models only Roaming to another networkInserting a SIM Removing a SIMUsing GPS select models only Using Bluetooth wireless devicesConnecting to a wired network Bluetooth and Internet Connection Sharing ICSConnecting a modem cable Connecting a country- or region-specific modem cable adapter Selecting a location settingAdding new locations when traveling Windows Select Start Devices and PrintersConnecting to a local area network LAN select models only Page Using the media activity controls MultimediaAudio Adjusting the volume Select Start All Programs Accessories Sound RecorderChecking audio functions on the computer Select Start Control Panel Hardware and Sound SoundWebcam select models only VideoPage Hdmi Configuring audio for Hdmi Intel Wireless Display select models onlyPower management Shutting down the computerWindows 7-SelectStart Shut down Setting power options Using power-saving statesInitiating and exiting Sleep Using the power meter Using power plansViewing the current power plan Initiating and exiting HibernationSelecting a different power plan Customizing power plansSetting password protection on wakeup Using HP Power Assistant select models only Using battery powerFinding additional battery information Select Start All Programs HP HP Power AssistantUsing Battery Check Displaying the remaining battery chargeMaximizing battery discharge time Managing low battery levelsConserving battery power Resolving a low battery levelUsing external AC power Storing a batteryDisposing of a used battery Replacing the batteryTesting an AC adapter Switchable graphics/dual graphics select models only Using switchable graphics select models onlyUsing dual graphics select models only Using Media Card Reader cards select models only External cards and devicesInserting a digital card Using ExpressCards select models only Configuring an ExpressCardRemoving a digital card Inserting an ExpressCard Using smart cards select models only Removing an ExpressCardUsing a USB device Inserting a smart cardRemoving a smart card Using 1394 devices select models only Connecting a USB deviceRemoving a USB device Using an eSATA device select models only Connecting a 1394 deviceRemoving a 1394 device Connecting an eSATA device Removing an eSATA deviceUsing a serial device select models only Using optional external devicesUsing optional external drives Using the expansion port select models only Using the docking connector select models only Drives Handling drivesUsing hard drives Using Disk DefragmenterUsing Disk Cleanup Improving hard drive performanceUsing HP 3D DriveGuard select models only Managing power with a parked hard driveIdentifying HP 3D DriveGuard status Using optical drives select models only Identifying the installed optical driveUsing HP 3D DriveGuard software Inserting an optical discRemoving an optical disc Slot-loadWhen the disc tray opens normally Slot-load Using RAID select models only Sharing optical drivesSecurity Protecting the computerUsing passwords Setting passwords in Windows Password FunctionSetting passwords in Computer Setup Managing a Bios administrator passwordSetting a new Bios administrator password Changing a Bios administrator passwordManaging a Computer Setup DriveLock password Entering a Bios administrator passwordDeleting a Bios administrator password Setting a DriveLock password Entering a DriveLock password Changing a DriveLock passwordRemoving DriveLock protection Using Computer Setup Automatic DriveLock Entering an Automatic DriveLock passwordRemoving Automatic DriveLock protection Using antivirus software Using firewall softwareInstalling critical security updates Using HP ProtectTools Security Manager select models only Installing an optional security cableUsing the fingerprint reader select models only Locating the fingerprint readerMaintenance Cleaning your computerCleaning products Cleaning proceduresCleaning the sides and cover Cleaning the TouchPad and keyboardUpdating programs and drivers Using SoftPaq Download Manager Computer Setup Bios and Advanced System Diagnostics Using Computer SetupStarting Computer Setup Navigating and selecting in Computer SetupRestoring factory settings in Computer Setup Updating the Bios Determining the Bios versionDownloading a Bios update Select Start Help and Support MaintainUsing Advanced System Diagnostics Page MultiBoot About the boot device orderEnabling boot devices in Computer Setup Considering boot order changesChoosing MultiBoot preferences Setting a new boot order in Computer SetupDynamically choosing a boot device using the f9 prompt Setting a MultiBoot Express promptEntering MultiBoot Express preferences Using Client Management Solutions Configuring and deploying a software imageComputer Management Managing and updating software HP Client Manager for Altiris select models onlyHP CCM Client Configuration Manager select models only HP SSM System Software ManagerUsing Intel Active Management Technology select models only Enabling the iAMT solutionUsing the MEBx setup utility menus Intel ME ConfigurationIAMT Configuration Change Intel ME PasswordTraveling with the computer Page Troubleshooting resources Electrostatic discharge Symbols/Numerics IndexKeys SIM