HP XU103UT manual Restoring factory settings in Computer Setup

Page 77

To exit Computer Setup menus, choose one of the following methods:

●To exit Computer Setup menus without saving your changes:

Click the Exit icon in the lower-left corner of the screen, and then follow the on-screen instructions.

– or –

Use the tab key and the arrow keys to select File > Ignore Changes and Exit, and then press enter.

●To save your changes and exit Computer Setup menus:

Click the Save icon in the lower-left corner of the screen, and then follow the on-screen instructions.

– or –

Use the tab key and the arrow keys to select File > Save Changes and Exit, and then press enter.

Your changes go into effect when the computer restarts.

Restoring factory settings in Computer Setup

NOTE: Restoring defaults will not change the hard drive mode.

To return all settings in Computer Setup to the values that were set at the factory, follow these steps:

1.Turn on or restart the computer, and then press esc while the “Press the ESC key for Startup Menu” message is displayed at the bottom of the screen.

2.Press f10 to enter Computer Setup.

3.Use a pointing device or the arrow keys to select File > Restore Defaults.

4.Follow the on-screen instructions.

5.To save your changes and exit, click the Save icon in the lower-left corner of the screen, and then follow the on-screen instructions.

– or –

Use the arrow keys to select File > Save Changes and Exit, and then press enter. Your changes go into effect when the computer restarts.

NOTE: Your password settings and security settings are not changed when you restore the factory settings.

Using Computer Setup 67

Image 77

Contents HP Notebook Product notice Safety warning notice Iv Safety warning notice Table of contents VGA Hdmi External cards and devices Security Computer Setup Bios and Advanced System Diagnostics Appendix C Electrostatic discharge Index Select Start All Programs HP HP Documentation IntroductionFinding more information about your new computer Identifying wireless and network status icons Creating a wireless connectionNetworking select models only WindowsWindows Vista Using HP Connection Manager select models only Turning wireless devices on or offUsing operating system controls Select Start All Programs HP HP Connection ManagerSelect Start Connect to Using a WlanConnecting to an existing Wlan Protecting your Wlan Setting up a new WlanRoaming to another network Using HP Mobile Broadband select models onlyRemoving a SIM Inserting a SIMUsing Bluetooth wireless devices Using GPS select models onlyConnecting to a wired network Bluetooth and Internet Connection Sharing ICSConnecting a modem cable Selecting a location setting Connecting a country- or region-specific modem cable adapterWindows Select Start Devices and Printers Adding new locations when travelingConnecting to a local area network LAN select models only Page Audio Using the media activity controlsMultimedia Select Start All Programs Accessories Sound Recorder Adjusting the volumeChecking audio functions on the computer Select Start Control Panel Hardware and Sound SoundVideo Webcam select models onlyPage Hdmi Intel Wireless Display select models only Configuring audio for HdmiWindows 7-SelectStart Shut down Power managementShutting down the computer Initiating and exiting Sleep Setting power optionsUsing power-saving states Using power plans Using the power meterViewing the current power plan Initiating and exiting HibernationCustomizing power plans Selecting a different power planSetting password protection on wakeup Using battery power Using HP Power Assistant select models onlyFinding additional battery information Select Start All Programs HP HP Power AssistantDisplaying the remaining battery charge Using Battery CheckMaximizing battery discharge time Managing low battery levelsResolving a low battery level Conserving battery powerStoring a battery Using external AC powerDisposing of a used battery Replacing the batteryTesting an AC adapter Using switchable graphics select models only Switchable graphics/dual graphics select models onlyUsing dual graphics select models only Inserting a digital card Using Media Card Reader cards select models onlyExternal cards and devices Removing a digital card Using ExpressCards select models onlyConfiguring an ExpressCard Inserting an ExpressCard Removing an ExpressCard Using smart cards select models onlyRemoving a smart card Using a USB deviceInserting a smart card Removing a USB device Using 1394 devices select models onlyConnecting a USB device Removing a 1394 device Using an eSATA device select models onlyConnecting a 1394 device Removing an eSATA device Connecting an eSATA deviceUsing optional external drives Using a serial device select models onlyUsing optional external devices Using the expansion port select models only Using the docking connector select models only Handling drives DrivesUsing Disk Defragmenter Using hard drivesUsing Disk Cleanup Improving hard drive performanceIdentifying HP 3D DriveGuard status Using HP 3D DriveGuard select models onlyManaging power with a parked hard drive Identifying the installed optical drive Using optical drives select models onlyUsing HP 3D DriveGuard software Inserting an optical discSlot-load Removing an optical discWhen the disc tray opens normally Slot-load Sharing optical drives Using RAID select models onlyProtecting the computer SecurityUsing passwords Password Function Setting passwords in WindowsManaging a Bios administrator password Setting passwords in Computer SetupSetting a new Bios administrator password Changing a Bios administrator passwordDeleting a Bios administrator password Managing a Computer Setup DriveLock passwordEntering a Bios administrator password Setting a DriveLock password Removing DriveLock protection Entering a DriveLock passwordChanging a DriveLock password Removing Automatic DriveLock protection Using Computer Setup Automatic DriveLockEntering an Automatic DriveLock password Installing critical security updates Using antivirus softwareUsing firewall software Installing an optional security cable Using HP ProtectTools Security Manager select models onlyLocating the fingerprint reader Using the fingerprint reader select models onlyCleaning your computer MaintenanceCleaning products Cleaning proceduresUpdating programs and drivers Cleaning the sides and coverCleaning the TouchPad and keyboard Using SoftPaq Download Manager Using Computer Setup Computer Setup Bios and Advanced System DiagnosticsStarting Computer Setup Navigating and selecting in Computer SetupRestoring factory settings in Computer Setup Determining the Bios version Updating the BiosDownloading a Bios update Select Start Help and Support MaintainUsing Advanced System Diagnostics Page About the boot device order MultiBootConsidering boot order changes Enabling boot devices in Computer SetupSetting a new boot order in Computer Setup Choosing MultiBoot preferencesEntering MultiBoot Express preferences Dynamically choosing a boot device using the f9 promptSetting a MultiBoot Express prompt Computer Management Using Client Management SolutionsConfiguring and deploying a software image HP Client Manager for Altiris select models only Managing and updating softwareHP SSM System Software Manager HP CCM Client Configuration Manager select models onlyEnabling the iAMT solution Using Intel Active Management Technology select models onlyUsing the MEBx setup utility menus Intel ME ConfigurationChange Intel ME Password IAMT ConfigurationTraveling with the computer Page Troubleshooting resources Electrostatic discharge Index Symbols/NumericsKeys SIM