HP LP 2000r Cable Management Accessory, Use Tie Kit Kit Contains HP Rack System/E, Mount Fastener

Page 18

HP Netserver High Density Rack Solutions Overview (LP 2000r)

To Tie Together the Following	Use Tie Kit	Kit Contains
HP Rack System/E	HP Model Number	Mount Fastener
	HP Model Number

2 each 41U racks (J1500A)	J1512B	2	Front Tie Brackets
		2 Rear Tie Brackets
		2-Part Cosmetic Cover

1 each 41U rack (J1500A) and	J1513B	2 Front Tie Brackets
1 each 33U rack (J1501A)		2 Rear Tie Brackets
		2-Part Cosmetic Cover

2 each 33U rack (J1501A)	J1513B	2 Front Tie Brackets
		2 Rear Tie Brackets
		2-Part Cosmetic Cover

Any combination	No kit available
that includes a 25U rack

Cable Management Accessory

The HP Netserver LP 2000r is delivered complete with slides ready for installation. However, if additional cable management is needed, the HP Rack Cable Management Kit (J1481A) comes in handy.

It offers a solution to route and organize cables in high-density rack environments. The kit contains four brackets for routing and channeling cables and 12 Velcro™ ties for securing and bundling. The J1481A is designed to offer a flexible and scaleable solution to accommodate various racking and cabling scenarios. Brackets can mount on both the left and right rear columns and can be used with both rail and slide rack- mounting. Multiple kits can be used in combination to provide additional cable man- agement as the rack density increases. Each bracket is designed to contain approxi- mately 30 large SCSI cables (1/2” diameter) or 120 LAN cables (1/4” diameter) or any combination of the two (i.e. 15 SCSI/60 LAN).

The Rack Cable Management Kit offers complete compatibility with HP System/E

Racks and industry standard non-HP racks.

13

Image 18

Contents Hp netserver high Density rack solutions Overview Planning your rack system for LP 2000rExecutive Summary Publications WebsitesHP Netserver website http//netserver.hp.com Reader Assumptions Table of Contents HP Netserver High Density Rack Solutions Overview LP 2000r Safety and Regulatory Information Safety WarningsGlossary HP Netserver High Density Rack Solutions Overview LP 2000r Determine power requirements for the servers Planning your racked systemCircuit breakers Power up sequencePower down sequence ServerInput Power watts x 3.41=Thermal dissipation BTU/hr Check your calculationsX 3.41 = 2,431 BTU/Hr Power consumption worksheet sample Category Part Number DescriptionPower consumption worksheet actual HP Rack System/E Gauge columns provide strength Anti-tip footVentilation Ease of Use StrengthMobility StabilityFront doors, side panels and tie kits HP Rack AccessoriesFor Use with HP Rack Model Number Content For Use with HP Rack Model NumberCable Management Accessory Use Tie Kit Kit Contains HP Rack System/EMount Fastener HP Power Distribution Options Voltage Current Outlets HP Product Number TypeE7675A E77671A E7676A HP Netserver High Density Rack Solutions Overview LP 2000r Uninterruptible Power Supplies UPS Power = Vol ts x AmpsConsole Switch Description IncludesAvailable Kit Contains HP Model Number HP Rackmount Flat Panel Monitor and KeyboardHP Rack System/E Vertical Extension Kit HP Vertical Extension Kit IncludesPost HP System/E racks or EIA standard cabinets InstallationFlexible installation options Slide mountingMarking the rack Marking Rack ColumnsPost EIA standard non-HP racks 3 options Fixed, center mountingFixed, flush mounting Marking the Rack Location Marks on the Racks Front ColumnsBefore you begin installation Preparing the HP Netserver for 2-post rack installationInstalling Power Distribution Units Installing the Uninterruptible Power SuppliesInstalling the servers PDUs can be mounted on the rearAttach the Cable Management Arm Cable ManagementHP System/E racks Attach the main cable guidesBegin routing the cables Secure each cable bundleRoute the cables to their destination Maintain the ambient temperature Conclusion HP Netserver High Density Rack Solutions Overview LP 2000r