HP LP 2000r manual Safety and Regulatory Information, Safety Warnings

Page 7

HP Netserver High Density Rack Solutions Overview (LP 2000r)

Safety and Regulatory Information

For your protection, Hewlett-Packard products are tested for conformance to various national and interna- tional regulations and standards. The scope of this regulatory testing includes electrical and mechanical safety, electromagnetic emissions, immunity, ESD, and hazardous materials.

Where required, certifications are obtained from third party test agencies. Certification marks, when required, appear on the product label. In addition, various regulatory bodies require some information under the headings below.

These products and related documentation must be reviewed for familiarization with safety markings and instructions before operation.

WARNING The WARNING sign denotes a hazard. It calls attention to a procedure, practice, or situation which, if not done correctly or adhered to, could result in injury. Do not proceed beyond a WARNING sign until the indicated conditions are fully understood and met.

CAUTION The CAUTION sign denotes a hazard. It calls attention to an operating procedure, practice, or situation which, if not done correctly or adhered to, could damage or destroy part or the entire product. Do not proceed beyond a CAUTION sign until the indicated conditions are fully understood and met.

Safety Warnings

The following warnings and cautions are applicable to the System/E rack. Please observe all safety precautions and warnings.

This product has not been evaluated for connection to an IT power system (an AC distribution system hav- ing no direct connection to earth (ground) according to EN60950.

Grounding

WARNING The HP System/E Racks are safety class I product and has a protective earthing (grounding) terminal. There must be an uninterruptible safety earth ground from the main power source to the product’s input wiring terminals, power cord, or supplied cord set. Whenever it is likely that the protection has been impaired, disconnect the power cord until the ground has been restored.

Leakage Current

WARNING Due to types of products that can be installed in the System/E rack, there is a risk of high leakage current (3.5 mA). Reliable ground circuit continuity is vital for safe operation of this product. To reduce the risk of electric shock, earth (ground) connection is essential before connecting the power supply. Never operate this cabinet with the ground conductor disconnected.

Power Limitations

CAUTION To reduce the risk of overload, do not load any single Power Distribution Unit (PDU) or IEC-320C19 receptacle with more than a maximum of 16 A. In addition, do not load a single NEMA 5-15 or IEC-320 C13 receptacle with more than a maximum of 10 A.

Cabinet Stability

CAUTION To reduce the risk of cabinet instability, deploy the anti-tip feet before installing or extending any devices. Extend only one device at a time. Do not stand or sit on any extended device. Qualified service personnel should do all non-operator servicing.

Accessories

CAUTION This product is designed for use with specific electrical accessories. The use of any other accessory is not recommended or supported.

2

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Planning your rack system for LP 2000r Hp netserver high Density rack solutions OverviewExecutive Summary Websites PublicationsHP Netserver website http//netserver.hp.com Reader Assumptions Table of Contents HP Netserver High Density Rack Solutions Overview LP 2000r Safety Warnings Safety and Regulatory InformationGlossary HP Netserver High Density Rack Solutions Overview LP 2000r Planning your racked system Determine power requirements for the serversServer Power up sequencePower down sequence Circuit breakersCheck your calculations Input Power watts x 3.41=Thermal dissipation BTU/hrX 3.41 = 2,431 BTU/Hr Category Part Number Description Power consumption worksheet samplePower consumption worksheet actual Gauge columns provide strength Anti-tip foot HP Rack System/EVentilation Stability StrengthMobility Ease of UseFor Use with HP Rack Model Number HP Rack AccessoriesFor Use with HP Rack Model Number Content Front doors, side panels and tie kitsUse Tie Kit Kit Contains HP Rack System/E Cable Management AccessoryMount Fastener Voltage Current Outlets HP Product Number Type HP Power Distribution OptionsE7675A E77671A E7676A HP Netserver High Density Rack Solutions Overview LP 2000r Power = Vol ts x Amps Uninterruptible Power Supplies UPSDescription Includes Console SwitchAvailable HP Vertical Extension Kit Includes HP Rackmount Flat Panel Monitor and KeyboardHP Rack System/E Vertical Extension Kit Kit Contains HP Model NumberSlide mounting InstallationFlexible installation options Post HP System/E racks or EIA standard cabinetsMarking Rack Columns Marking the rackFixed, center mounting Post EIA standard non-HP racks 3 optionsFixed, flush mounting Location Marks on the Racks Front Columns Marking the RackPreparing the HP Netserver for 2-post rack installation Before you begin installationPDUs can be mounted on the rear Installing the Uninterruptible Power SuppliesInstalling the servers Installing Power Distribution UnitsAttach the main cable guides Cable ManagementHP System/E racks Attach the Cable Management ArmSecure each cable bundle Begin routing the cablesRoute the cables to their destination Maintain the ambient temperature Conclusion HP Netserver High Density Rack Solutions Overview LP 2000r
Top Page Image Contents