HP AA-RSB6B-TE manual How to Change the Core PID Format

Page 52

Installing the SAN Switch 2/8

6.To view the Core Switch PID setting, press Enter until you reach the Core Switch PID format line, similar to the following.

Core Switch PID Format: (0..1) [0]

Note: The [0] value shown above indicates the Core Switch PID parameter set on this particular switch.

7.Continue to press Enter until the admin prompt displays.

8.Type switchEnable and press Enter.

If necessary, proceed to the next section to change the Core PID setting to match all switches that will reside in the SAN.

How to Change the Core PID Format

Note: HP switches ship with the Core switch PID set to 1. HP recommends that if you are in the process of creating a new SAN, set the PID to 1 for all switches in the SAN.

In order for the switches to interoperate properly, all of them must have the same Core PID format. Use these steps to change the Core PID format, if necessary.

Caution: If you need to change the PID format on this new switch, change the

PID format before connecting the fiber cables.

1.If the switch is configured for zoning, type cfgDisable to disable zoning.

2.To disable the switch, type SwitchDisable.

3.To reset the PID format, use the “configure” telnet command. Type configure. The following displays:

Configure...

4.Type y at the Fabric parameters prompt, Fabric parameters (yes, y, no, n): [no] y

5.Locate the line, "Core Switch PID Format: (0..1) [0] 1," and type 1.

6.Press Enter until the following prompt appears.

52

hp StorageWorks SAN Switch 2/8 Installation Guide

Image 52
Contents Hp StorageWorks SAN switch 2/8 Page Contents Contents Regulatory Compliance Notices Electrostatic Discharge Technical SpecificationsTables Contents Contents About this Guide Intended Audience OverviewRelated Documentation Conventions Text SymbolsDocument Conventions Equipment Symbols About this Guide Rack Stability Rack stability protects personal and equipmentHP Technical Support Getting HelpHP Storage Website HP Authorized Reseller Overview1 Firmware SAN Switch 2/8 FeaturesHardware SFP Media Side Fan Side Accessory Part Number Optional Hardware KitsOverview Installing SAN Switch 2/8 Check the License Installed Four Switch Limitation ErrorsFour Switch Limitation CLI Error Messages Violation Timer Errors Four Switch Limitation Workarounds Unpack and Verify Carton Contents Number Description Selecting an Operating Location Installation and Safety GuidelinesCooling Requirements Power Requirements Installing the Switch as a Stand-alone Unit Installing the Fixed Rail Kit Attaching the Fixed Rack Mount Kit rails to the switch Connecting the power cord Optional HP System/e Rack Items Required for the HP System/e RackInstalling the SAN Switch 2/8 Installing the Switch in the Optional HP System/e Rack Installing the rear rail tray brackets Installing the tinnerman clips Installing the rubber washers Assembling the outer rails Assembling the inner rails Installing the switch into an HP Rack Securing the switch Power On Self-Test Setting Network Addresses via a Serial Connection Configuring SAN Switch 2/8 Network AddressingRequirements Connecting the Serial cable To configure port settings in a Unix environment, type Connecting the SAN Switch 2/8 to the LAN Connecting the Ethernet cableImportant Information on Setting the Core PID Format How to Check the Current Core PID SettingHow to Change the Core PID Format Modifying Domain IDs Specifying Custom Status Policies Connecting a Cable to an SFP Module Verifying Operation Inserting a cable into an SFPInstalling Multiple Switches into an Existing SAN Cascading Switches Managing SAN Switch 2/8 Interpreting LED Activity Front Panel LEDsLED Port Speed Ethernet Link Rear Panel LED Management Overview Displaying the Optional Feature Licenses Enabling Licensed FeaturesLogging into the SAN Switch 2/8 Running Basic Switch Operations Using TelnetChanging the Admin Password and User ID Configuring the IP and Fibre Channel Address Displaying Devices within the Fabric Setting the Switch Date and TimeChecking the Firmware Version Displaying Switch Configuration Settings SAN Switch 2/8 Diagnostic TestsInterpreting Post Results Diagnostic Tests Managing the SAN Switch 2/8 Saving Configuration Settings Upgrading Firmware Backing Up System Configuration Settings Restoring the System Configuration Settings FastBootUpgrading or Restoring the Switch Firmware Downloading Firmware from the HP WebsiteRegulatory Compliance Notices FCC EMC Statement USAEMC Statement Canada EMC Statement European UnionSpécification ATI Classe a France Germany Noise DeclarationRegulatory Compliance Notices Laser Safety Certification and Classification InformationBattery Replacement Notice Regulatory Compliance Notices Electrostatic Discharge Grounding Methods Technical Specifications Dimensions Power Supply SpecificationsMemory Specifications Environmental RequirementsSerial Port Specifications PINAlpa APIAsic ATMAwtov BERDLS CRCEdtov FC-AL-3 FC-FLAFcia FCPFlogi FsaccHBA ISLMIB LIPNAA Plogi Post RatovRrtov RscnRxid SANSwitch Translative ModeTarget TenancyUDP UlptovULP WWNIndex Network addressing Hp StorageWorks SAN Switch 2/8 Installation Guide 103 104