Enww

NOTE: See Table A-2 Media sizes on page 83 for a list of supported media sizes.

1.If installed, detach the rigid media input and output tables from the printer, and set them aside.

2.Install the takeup spindle and empty cardboard core, see (8).

3.Load the media centered onto the supply spindle (1).

NOTE: To prevent fingerprints from showing on printed output, wear gloves while handling the media.

4.Load the supply spindle onto the supply system bracket, with the media centered.

You can print on either side of the media by loading the spindle so the media spools off the bottom of the roll or the top of the roll.

5.Configure the media as explained in Configure media on page 9. At the end of the Configure Media process, press Proceed on the control panel.

If the media is already configured, from the Home page of the control panel, press Load.

NOTE: Be sure to enter the correct media thickness. The printer can detect the thickness of sheet-fed media only if the media is loaded under the media thickness sensor, which is located at the user end of the carriage rail. For roll-fed media (if enabled), use the manufacturer's specification or use a caliper to measure the thickness.

The control panel displays a graphic and prompts you to remove the foam press roller.

6.As prompted by the control panel, raise the foam press roller (3) to the upper position, then press Proceed.

7.Pull the media from the roll, pull it over the foam lift roller (2) (the foam press roller (3) should not be in position yet) and lay it on the belt up to the input media roller (4). Then press Proceed.

TIP: The foam lift roller and foam press roller are intended for flexible roll medias such as scrim vinyls. Using the foam rollers may cause media feed errors with heavier, less flexible roll stock such as photobase papers. When printing on heavier stock, feed the media underneath both rollers to bypass them.

8.On the control panel, press the upper (forward) Advance Media arrow button to advance the media, with the vacuum fans on.

You may need to hold the media down on the belt until the vacuum grabs it.

9.Advance the media until it hangs on exit side down to the takeup roller. Do not tape the media to the core at this time.

10.On the control panel, press Turn Off Fans.

11.Hold the upper (forward) Advance Media button down for about five seconds.

This will help smooth out wrinkles and equalize the tension of the media across the belt.

Since the fans are off, the media should not advance. If the media moves, hold onto the media with your right hand while pressing Advance Media with your left hand.

12.Place the foam press roller (3) into operating position. Then press Proceed.

13.On the control panel, press Turn On Fans.

14.Lower the input (4) and output media rollers (5) to their operating positions.

15.Check for wrinkles in the media across the full length and width of the belt.

16 Chapter 2 Configure and load media

Scitex FB700 Industrial specifications

The HP Scitex FB700 is an industrial flatbed printer designed to meet the rigorous demands of high-quality large-format printing. Launched by HP, this printer offers businesses incredible versatility, speed, and precision, making it an essential tool for print service providers looking to enhance their productivity and expand their service offerings.

One of the standout features of the HP Scitex FB700 is its print quality. Equipped with HP's proprietary UV inks, the printer delivers vibrant colors, sharp images, and excellent durability. These inks are designed for a wide range of substrates, making it possible to print on materials such as rigid boards, flexible media, and even specialty applications like textiles. The FB700 supports a maximum print resolution of 1200 dpi, ensuring that every detail is faithfully rendered.

A key technology in the FB700 is its UV curing capability. This technology allows the printer to cure the inks almost instantly as they are applied, which not only speeds up the printing process but also enables printing on heat-sensitive materials. The ability to quickly switch between different substrates, from foam board to acrylic, offers unparalleled flexibility for businesses looking to meet diverse client needs.

Moreover, the HP Scitex FB700 features a user-friendly interface, enhanced by HP’s smart technology. This includes automated calibration and quality control systems that help maintain consistent print quality while reducing the likelihood of errors. The printer is also designed with ease of maintenance in mind, allowing operators to focus on production rather than troubleshooting.

In terms of productivity, the FB700 excels with a high throughput rate. Capable of producing prints up to 95 m² per hour, this printer is suited for high-volume jobs, enabling businesses to take on larger projects without sacrificing quality. Its robust design ensures reliability and efficiency, making it ideal for busy print environments.

Lastly, sustainability is an important consideration within the printing industry, and the HP Scitex FB700 addresses this concern by utilizing low-VOC inks and energy-efficient components. This commitment to eco-friendliness allows companies to meet their sustainability goals while maintaining a competitive edge in the market.

In summary, the HP Scitex FB700 Industrial printer is a powerful tool that combines high performance, versatility, and ease of use. With its advanced printing technologies, exceptional print quality, and commitment to sustainability, it is well-equipped to handle the diverse demands of modern printing applications.