HP 8000s manual Declares that the product, Conforms to the following product specifications

Page 226

Legal information

DECLARATION OF CONFORMITY

according to ISO/IEC Guide 22 and EN 45014

Supplier’s name:	Hewlett-Packard Company

Supplier’s address:	Avda. Graells, 501
	08174 Sant Cugat del Vallès
	Barcelona, Spain

declares that the product

Regulatory Model (3):	BCLAA-0502 and BCLAA-0602

Product family:	HP Designjet 8000s Printer series and HP Designjet 8000s Take-up Reel Kit

Product options:	All

conforms to the following product specifications

Safety:	IEC 60950-1:2001 / EN 60950–1:2001

EMC:	CISPR 22:1997 +A1:2000 +A2:2002 / EN 55022:98 +A1:2000 +A2:2003 Class A
	(1)(3)
	EN 55024:1998 +A1:2001 +A2:2003
	EN 61000-3-2:2000/ IEC 61000-3-2:2000
	EN 61000-3-3:1995+A1:2001/ IEC 61000-3-3/A1:2001
	FCC Title 47 CFR, Part 15 Class A (2) (3)

Additional information

The product herewith complies with the requirements of the Low-Voltage Directive 73/23/EEC and the EMC Directive 89/336/EEC, and carries the CE marking accordingly.

1.The product was tested in a typical configuration with HP Personal Computer systems and peripherals.

2.This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

●This device may not cause harmful interference.

●This device must accept any interference received, including interference that may cause undesired operation.

3.The product is assigned a Regulatory Model Number which stays with the regulatory aspect of the design. The Regulatory Model Number is the main product identifier in the regulatory documentation and test reports; this number should not be confused with the marketing name or the product numbers.

216

Chapter 19 Legal information

ENWW

Image 226

Contents HP Designjet 8000s Printer series Legal notices Table of contents How do I… printing topics Problem is… troubleshooting topics Tell me about media 177 Tell me about… printer specifications topics 219 Enww Introduction IntroductionUsing this guide Printers main componentsFront view Rear view HeatersPrinters front panel Introduction Safety precautions General warningsGeneral cautions Regular inspection and maintenance Handling precautionsPower supply PrinterIntroduction How do I… basic operation topics? System configuration connection exampleConnection procedure Connect to a computerHow do I… basic operation topics? How do I… basic operation topics? Turn the power on/off Turn on the printer How do I turn the power off How do I… basic operation topics? Check the firmware version How do I load/unload media Install a media roll in the printer How do I load/unload media How do I load/unload media How do I load/unload media How do I load/unload media How do I load/unload media How do I load/unload media How do I load/unload media How do I load/unload media How do I load/unload media How do I load/unload media How do I load/unload media Paper Remove a media roll from the printer How do I load/unload media Replace a jammed media roll Load a cut sheetHow do I load/unload media Load a cut sheet How do I load/unload media How do I load/unload media Glossy Matte Banner Bltb Backlit How do I load/unload media Use the media edge guards Use the media cutter Use the media cutter How do I load/unload media Use the take-up reel Set the take-up reel winding direction Define the take-up reel winding mode Load media on to the take-up reel How do I load/unload media How do I load/unload media How do I load/unload media How do I load/unload media How do I load/unload media Take-up reel horizontal alignment How do I load/unload media How do I load/unload media How do I… printing topics Perform a manual form feed/rewindUse manual nesting How do I… printing topicsIncrease/reduce pressure on media How do I… printing topics How do I… ink topics Replace an ink cartridgeChange the printhead height How do I… ink topics How do I… ink topics Tighten the printhead carriage fixing screws How do I… ink topics Regular maintenance guide How do I maintain the printerHow do I maintain the printer Daily maintenance Capping unit cleaning How do I maintain the printer How do I maintain the printer How do I maintain the printer How do I maintain the printer How do I maintain the printer Wiper liquid bottle replacement Wiper liquid bottle replacement How do I maintain the printer Insert the wiper liquid dispenser cap How do I maintain the printer How do I maintain the printer Wiper sponge replacement Wiper sponge replacement How do I maintain the printer How do I maintain the printer How do I maintain the printer How do I maintain the printer Wiper blade replacement Wiper blade replacement Open the right maintenance cover How do I maintain the printer How do I maintain the printer How do I maintain the printer Clean ink system Prepare for extended power down two to four weeks Ink system storage Charge the ink system Clean the exterior of the printer Clean the carriage baseClean the carriage base Clean the front cover and media feed Clean the platen How do I maintain the printer Waste ink bottle replacement How do I maintain the printer Waste ink bottle replacement 105 Normal printhead recovery Normal printhead recovery 107 Print the nozzle print pattern Print the nozzle print pattern 109 110 How do I maintain the printer How do I get the best image quality Test the image quality Interpreting the print quality Manage media types Copy a media type to create a new oneCreate a new media type Modify media type settings Delete a media type How do I calibrate my printer Calibrate media advanceHow do I calibrate my printer 119 How do I get the best image quality Printhead position adjustment How do I get the best image quality How do I calibrate my printer 123 Printhead nozzle position adjustment Line sensor position adjustment Back feed adjustment print126 How do I get the best image quality Adjust heater and print mode settings PanelParameters Adjust heater and print mode settings 129 130 How do I get the best image quality Problem is… troubleshooting topics Problem is… checklist Symptom Items to be checked Corrective measuresProblem is… checklist 133 Printhead crash Load media again See How do I load/unload media Ink cartridge is near expiration date Ink cartridge is not installedInk cartridge is not detected Ink cartridge has passed its expiration dateAn error message Service errorsOperator error messages Service error messagesMedia Other messages Problem is an abnormal sound 142 Problem is… troubleshooting topics Problem is print quality This section explains how to solve print quality problemsProblem is print quality Tell me about… basic knowledge topics Tell me about operating conditions Installation spaceEnvironmental conditions Tell me about the power supply PowerExhaust attachment Tell me about front panel messages and printer stateHP Designjet High Speed Dryer Messages on the front panelOnline state print mode display Offline menu mode display Shutdown state display 152 Tell me about… basic knowledge topics Storing media Tell me about mediaDisposing of media Other precautions Using mediaHandling prints Tell me about the ink system Ink CartridgesTell me about the ink system Ink cartridge storage and disposal Replacing an ink cartridgeHP 780 Waste Ink Bottle HP Cleaning Swabs HP Cap Cleaning Kit with RollerHP 780 Wiper Cleaning Liquid Precautions for handling the waste ink bottleHP Ink System Cleaning Kit HP Ink System Storage Kit160 Tell me about the ink system Tell me about waste management Disposing of wasteTell me about waste management General recommendations 164 Tell me about waste management Tell me about… menus Menu operations Menu structureTo define a value Character list Media menu INK menu & messagesReplacing an empty ink cartridge Media REG menu Selecting a media type number Select Media Setting a media type name Rename MediaMedia advance value Media ADV Value Print direction setting Print Direction Print mode setting Print ModeDry time value DRY Time Value Flatten time Flatten Time Use media edge guard USE Edge GuardMedia advance mode Media ADV Mode Take-up reel mode TUR ModeLeading edge mode Leading Edge Vacuum level setting Vacuum LevelTell me about… menus Printhead height setting PH Height VAL Color stripe setting Color StripeBidirectional print position adjustment Bidir DEF Value Printhead cleaning mode PH Cleaning Media back feed adjustment Back Adjust VAL Media advance preference Advance PrefHeater preference Heater Pref Print mode preference Print Mode PrefPrinthead rest period PH Rest Period Delete a media type Delete Media Printhead temperature rest PH Temp RestSet remaining media SET Remaining Media Copy a media type Copy MediaDefault values for media types Media advance calibrationMedia advance calibration print Parameters Rough or DetailPH. Main menu Media back feed adjustment valueCap cleaning CAP Cleaning Ink system optimization INK SYS OPTReplace wiper sponge Replace Wipe Sponge Replace wiper cleaning liquid Replace Wipe LiquidReplace wiper blade Replace Wiper Blade Washing the printheads Wash PrintheadsReplace Printhead Replace Printhead PH. REC menuPrinthead height PH Height ADJ Reseat Printhead Reseat PrintheadRewind option Configuration print Config PrintFeed option Printer menuAdjustment pattern prints Test Prints Adjust menuError log information print Error LOG Print History print History PrintBidirectional print position adjustment Bidir DEF Printhead position adjustment #PH to PH VALBidirectional print position fine adjustment Bidir Fine Line sensor top position LS ADJ TOP VAL Setup menuNozzle position Nozzle POS VAL Line sensor side position LS ADJ Side VALLanguage for front panel Language Temperature units Temperature UnitsBoot version display Boot Version Time Zone Time Zone GMT+ICB board version display Carriage PCA Firmware version display Printer FW VERMain PCA version display Main PCA VER Asic version display Asic VERHeater delay time Heater Delay Time Factory default setting Factory DefaultPrinter firmware upgrade Printer FW Upgrade Heater menuHeater standby time Heater Standby Time Tell me about… heater topics HeatersHeater temperature settings Heater preset temperature by mediumFlow of heater temperature setting Temperature control Maintaining the preset temperatureHeater error messages 200 Tell me about… heater topics Tell me about… printer specifications topics Specifications Specification / FunctionEcological specifications 204 Tell me about… printer specifications topics Tell me about… ordering supplies and accessories topics Ordering supplies Ordering mediaOrdering accessories HP Media208 Tell me about… ordering supplies and accessories topics Tell me about… getting help topics HP Customer CareHP Designjet Online Extent of HP Limited Warranty Legal information212 Legal information Local law Regulatory noticesLimitations of liability Regulatory Model NumberNormes de sécurité Canada FCC statements U.S.AShielded cables DOC statement CanadaRegulatory notices 215 Declares that the product Conforms to the following product specificationsAdditional information Local contacts for regulatory topics only 218 Legal information Accessories IndexEnww

Related manuals

Manual 6 pages 61.09 Kb