HP 8000s manual Daily maintenance

Page 79

Category	Inspection/Maintenance	See

To leave the printer in or return it from a	Contact HP Support.
power off state of more than four weeks

Other	A service call error message will be
	displayed on the front panel. Contact HP
	Support.

Daily maintenance

WARNING! Failure to perform daily maintenance procedures may result in damage to your printheads and will invalidate your warranty.

CAUTION If you need to leave the printer unattended for any reason, ensure that the printer is on, the ink cartridges are full, the waste ink bottle is empty, and media is loaded so that automatic maintenance (performed regularly after the last printing process) can be completed successfully for the time you are not present. If needed, install new ink cartridges. The ink cartridges that you replace can be reused when you return to your printer, if they still contain ink. The ink cartridges must be stored properly and should not be used again if 3 months passed the install by date (on the product label).

Daily printhead maintenance will ensure optimal print quality and the life of your printheads. The ink in your HP Designjet 8000s Printer dries very quickly, so maintenance procedures ensure that the ink does not dry in the capping unit, the wiper blades, the ink tubes and printheads.

When the following message is displayed, immediately perform daily maintenance procedures:

How do I maintain the printer

●Clean the capping unit.

●Check the wiper liquid level.

●Check the waste ink bottle level

●Perform Normal printhead cleaning

●Print the NOZZLE PRINT pattern

NOTE Perform the above every day before printing.

Always use the specified cleaning liquid and cleaning equipment.

ENWW

Daily maintenance

69

Image 79

Contents HP Designjet 8000s Printer series Legal notices Table of contents How do I… printing topics Problem is… troubleshooting topics Tell me about media 177 Tell me about… printer specifications topics 219 Enww Introduction IntroductionPrinters main components Using this guideFront view Heaters Rear viewPrinters front panel Introduction General warnings Safety precautionsGeneral cautions Printer Handling precautionsPower supply Regular inspection and maintenanceIntroduction Connect to a computer System configuration connection exampleConnection procedure How do I… basic operation topics?How do I… basic operation topics? How do I… basic operation topics? Turn the power on/off Turn on the printer How do I turn the power off How do I… basic operation topics? Check the firmware version How do I load/unload media Install a media roll in the printer How do I load/unload media How do I load/unload media How do I load/unload media How do I load/unload media How do I load/unload media How do I load/unload media How do I load/unload media How do I load/unload media How do I load/unload media How do I load/unload media How do I load/unload media Paper Remove a media roll from the printer How do I load/unload media Load a cut sheet Replace a jammed media rollHow do I load/unload media Load a cut sheet How do I load/unload media How do I load/unload media Glossy Matte Banner Bltb Backlit How do I load/unload media Use the media edge guards Use the media cutter Use the media cutter How do I load/unload media Use the take-up reel Set the take-up reel winding direction Define the take-up reel winding mode Load media on to the take-up reel How do I load/unload media How do I load/unload media How do I load/unload media How do I load/unload media How do I load/unload media Take-up reel horizontal alignment How do I load/unload media How do I load/unload media Perform a manual form feed/rewind How do I… printing topicsHow do I… printing topics Use manual nestingIncrease/reduce pressure on media How do I… printing topics Replace an ink cartridge How do I… ink topicsChange the printhead height How do I… ink topics How do I… ink topics Tighten the printhead carriage fixing screws How do I… ink topics How do I maintain the printer Regular maintenance guideHow do I maintain the printer Daily maintenance Capping unit cleaning How do I maintain the printer How do I maintain the printer How do I maintain the printer How do I maintain the printer How do I maintain the printer Wiper liquid bottle replacement Wiper liquid bottle replacement How do I maintain the printer Insert the wiper liquid dispenser cap How do I maintain the printer How do I maintain the printer Wiper sponge replacement Wiper sponge replacement How do I maintain the printer How do I maintain the printer How do I maintain the printer How do I maintain the printer Wiper blade replacement Wiper blade replacement Open the right maintenance cover How do I maintain the printer How do I maintain the printer How do I maintain the printer Clean ink system Prepare for extended power down two to four weeks Ink system storage Charge the ink system Clean the carriage base Clean the exterior of the printerClean the carriage base Clean the front cover and media feed Clean the platen How do I maintain the printer Waste ink bottle replacement How do I maintain the printer Waste ink bottle replacement 105 Normal printhead recovery Normal printhead recovery 107 Print the nozzle print pattern Print the nozzle print pattern 109 110 How do I maintain the printer How do I get the best image quality Test the image quality Interpreting the print quality Copy a media type to create a new one Manage media typesCreate a new media type Modify media type settings Delete a media type Calibrate media advance How do I calibrate my printerHow do I calibrate my printer 119 How do I get the best image quality Printhead position adjustment How do I get the best image quality How do I calibrate my printer 123 Printhead nozzle position adjustment Back feed adjustment print Line sensor position adjustment126 How do I get the best image quality Panel Adjust heater and print mode settingsParameters Adjust heater and print mode settings 129 130 How do I get the best image quality Problem is… troubleshooting topics Symptom Items to be checked Corrective measures Problem is… checklistProblem is… checklist 133 Printhead crash Load media again See How do I load/unload media Ink cartridge has passed its expiration date Ink cartridge is not installedInk cartridge is not detected Ink cartridge is near expiration dateService errors An error messageService error messages Operator error messagesMedia Other messages Problem is an abnormal sound 142 Problem is… troubleshooting topics This section explains how to solve print quality problems Problem is print qualityProblem is print quality Tell me about… basic knowledge topics Tell me about operating conditions Installation spaceEnvironmental conditions Power Tell me about the power supplyMessages on the front panel Tell me about front panel messages and printer stateHP Designjet High Speed Dryer Exhaust attachmentOnline state print mode display Offline menu mode display Shutdown state display 152 Tell me about… basic knowledge topics Storing media Tell me about mediaDisposing of media Other precautions Using mediaHandling prints Ink Cartridges Tell me about the ink systemTell me about the ink system Ink cartridge storage and disposal Replacing an ink cartridgeHP 780 Waste Ink Bottle Precautions for handling the waste ink bottle HP Cap Cleaning Kit with RollerHP 780 Wiper Cleaning Liquid HP Cleaning SwabsHP Ink System Storage Kit HP Ink System Cleaning Kit160 Tell me about the ink system Disposing of waste Tell me about waste managementTell me about waste management General recommendations 164 Tell me about waste management Tell me about… menus Menu structure Menu operationsTo define a value Character list Media menu INK menu & messagesReplacing an empty ink cartridge Media REG menu Selecting a media type number Select Media Setting a media type name Rename MediaMedia advance value Media ADV Value Print direction setting Print Direction Print mode setting Print ModeDry time value DRY Time Value Use media edge guard USE Edge Guard Flatten time Flatten TimeTake-up reel mode TUR Mode Media advance mode Media ADV ModeVacuum level setting Vacuum Level Leading edge mode Leading EdgeTell me about… menus Printhead height setting PH Height VAL Color stripe setting Color StripeBidirectional print position adjustment Bidir DEF Value Printhead cleaning mode PH Cleaning Media advance preference Advance Pref Media back feed adjustment Back Adjust VALHeater preference Heater Pref Print mode preference Print Mode PrefPrinthead rest period PH Rest Period Copy a media type Copy Media Printhead temperature rest PH Temp RestSet remaining media SET Remaining Media Delete a media type Delete MediaMedia advance calibration Default values for media typesParameters Rough or Detail Media advance calibration printInk system optimization INK SYS OPT Media back feed adjustment valueCap cleaning CAP Cleaning PH. Main menuWashing the printheads Wash Printheads Replace wiper cleaning liquid Replace Wipe LiquidReplace wiper blade Replace Wiper Blade Replace wiper sponge Replace Wipe SpongeReseat Printhead Reseat Printhead PH. REC menuPrinthead height PH Height ADJ Replace Printhead Replace PrintheadPrinter menu Configuration print Config PrintFeed option Rewind optionHistory print History Print Adjust menuError log information print Error LOG Print Adjustment pattern prints Test PrintsBidirectional print position adjustment Bidir DEF Printhead position adjustment #PH to PH VALBidirectional print position fine adjustment Bidir Fine Line sensor side position LS ADJ Side VAL Setup menuNozzle position Nozzle POS VAL Line sensor top position LS ADJ TOP VALTime Zone Time Zone GMT+ Temperature units Temperature UnitsBoot version display Boot Version Language for front panel LanguageAsic version display Asic VER Firmware version display Printer FW VERMain PCA version display Main PCA VER ICB board version display Carriage PCAHeater menu Factory default setting Factory DefaultPrinter firmware upgrade Printer FW Upgrade Heater delay time Heater Delay TimeHeater standby time Heater Standby Time Heaters Tell me about… heater topicsHeater preset temperature by medium Heater temperature settingsFlow of heater temperature setting Maintaining the preset temperature Temperature controlHeater error messages 200 Tell me about… heater topics Tell me about… printer specifications topics Specification / Function SpecificationsEcological specifications 204 Tell me about… printer specifications topics Tell me about… ordering supplies and accessories topics Ordering media Ordering suppliesHP Media Ordering accessories208 Tell me about… ordering supplies and accessories topics HP Customer Care Tell me about… getting help topicsHP Designjet Online Legal information Extent of HP Limited Warranty212 Legal information Regulatory Model Number Regulatory noticesLimitations of liability Local lawDOC statement Canada FCC statements U.S.AShielded cables Normes de sécurité CanadaRegulatory notices 215 Declares that the product Conforms to the following product specificationsAdditional information Local contacts for regulatory topics only 218 Legal information Index AccessoriesEnww

Related manuals

Manual 6 pages 61.09 Kb