Thermo Products PHCFA072DV4R operation manual Fig-3

Page 11

NOTICE: Ventor assembly must be installed so that it is level. If unit is not level, condensate will leak in to ventor box thru inducer and potentially freeze.

1.The OHC must be installed with the side-wall ventor/ blower assembly. Do Not attempt to operate the OHC without the ventor assembly as this could result in damage to the appliance or home.

2.No clearance is required from the outer surface of the ventor assembly to combustible materials for fire hazard prevention.

3.The ventor is designed to fit in between the joist space of 16 O.C.

4.Maximum wall thickness for the ventor assembly is 12”.

Fig-3

5.Remove vent system components from box and inspect for damage. If the carton has been crushed or mutilated, check components very carefully for damage. DO NOT install if any damage is apparent.

6.Remove the vent tee from the vent pipe. Set the tee aside for now. Remove the exterior plate also.

7.See Fig. 3 for vent terminal location. As a general rule, location of the termination of the venting system should be installed in accordance with the National Fuel Gas Code, ANSI Z223.1, manufacturer’s recommendations, and/or local codes that are applicable. Refer to the following requirements or See Fig. 3 for typical locations.

8

Image 11
Contents OHCFA072DV4R OIL Fired FurnaceContents = Front = Highboy D = DownflowCAUTION do not Attempt to Start the Burner When Safety SectionWARNING and Cautions Page Codes and Clearances OHCFA072DV4R Combustible materialNon-combustible material HighboyII. General Instructions Venting Fig-1 Fig-2 Installation of VentorFig-3 Page Fig-4 Condensate Drain Line ConnectionsDuct WORK/AIR Conditioning Air Filter Mounted External to Furnace Ft/min Maximum Model Number Filter Type Air VelocityOHC Fig-7 Burner InstallationBurner Specifications and Applications Limit Position and Location75,000 72,000 OIL Tank and PipingRiello BTU/HR OHCFA072DV4RPage Room Thermostat Electrical WiringElectrical Connections Electronic Air Cleaner EAC and Humidifier Installation Post-Purge TimerBlower Motor Speed Selection Thermostat Anticipator SettingAlterations REQ’D for A/C @ Design External Static Pressure OHCFA072DV4Inputs Terminal Definitions & Field WiringBlower Controller Information for ECM Motor Outputs Operating Modes On and OFF Blower Delay Time Switch Settings Diagnostic Features Trouble ShootingStartup Procedures Sequence of Operation for the OHC To Turn Off Oil to AppliancePage Page Setting Supply Air Temperature Rise Adjustment Of Heat Input RateCheckout Procedure  Caution do not Attempt to Make Repairs Yourself Filter Cleaning and LocationIII. Users Information Section Inspection AreasIV. Installers Instructions to User General Inspection Dealer Maintenance Safety During Servicing and InspectionHeat Exchanger Cleaning Instructions Page Fig-12 Fig-13 SUPPLY/RETURN AIR Filter Filter maintenance procedureElectrical System SUPPLY/RETURN AIR BlowerOn Shutdown Filter replacementExtended Appliance Shutdown On Startup VI. HOMEOWNER/USER Information and Routine Maintenance Fig-16 Page Page Page Page Page Page Customer Appendix a Replacement Parts OHC BF3 Riello Burner Page Appendix B Wiring Diagram

PHCFA072DV4R specifications

The Thermo Products PHCFA072DV4R is a cutting-edge heating and cooling solution designed for modern residential and light commercial applications. This unit stands out due to its efficient performance and advanced technology. One of the most remarkable features of the PHCFA072DV4R is its energy efficiency. It boasts a high SEER rating that ensures reduced energy consumption without sacrificing comfort, making it an environmentally friendly choice for homeowners.

This system utilizes an inverter-driven compressor, which allows for variable speed operation. This means that the unit can adjust its output to match the specific heating or cooling needs of a space, providing more consistent temperatures and enhanced comfort. Additionally, this inverter technology minimizes noise levels, making the PHCFA072DV4R a quieter option compared to traditional fixed-speed systems.

Another noteworthy characteristic of the PHCFA072DV4R is its advanced filtration system. It is equipped with high-efficiency filters that effectively capture dust, pollen, and other airborne particles, ensuring improved indoor air quality. For those who suffer from allergies or have respiratory issues, this feature can provide significant relief.

The unit offers a user-friendly interface with a smart thermostat that enables users to control the system remotely. Through a mobile app, homeowners can adjust settings, set schedules, and monitor energy usage from anywhere, which adds a layer of convenience to the overall user experience.

Additionally, the PHCFA072DV4R is built with durability in mind. Its robust construction and high-quality materials ensure long-term reliability, reducing the likelihood of costly repairs. It also comes with a warranty that reflects the manufacturer's confidence in the product's performance.

Overall, the Thermo Products PHCFA072DV4R encapsulates efficiency, comfort, and advanced technology in a single package. Its ability to adapt to varying conditions, combined with features focused on air quality and ease of use, make it a prime choice for anyone looking for a versatile heating and cooling solution. This unit not only meets the demands of today's consumers but also aligns with sustainable practices, making it an ideal addition to any home or business.