Thermo Products PHCFA072DV4R operation manual

Page 30

1.Call for heat TSTAT closes sending 24 volts to “W”.

2.The 24 volt relay closes sending 115v to the inducer in the ventor assembly.

3.The inducer comes up to speed and provides flow and pressure which closes the pressure switch.

4.Upon this pressure switch closing, T & T are closed to bring on the burner.

To initially fire the oil burner, proceed in the following manner:

a.Turn the disconnecting switch, which provides power to the appliance, to the "OFF" position.

b.Set the room thermostat above room temperature.

c.Verify the oil tank is filled with sufficient fuel oil to operate the appliance.

d.Open all valves in the oil supply line to the burner.

e.Remove the burner compartment cover from the appliance.

f.Turn the disconnecting switch to “ON”.

g.Prime the pump to remove air in the oil supply line.

•See Riello Burner Manual included.

h.The burner has been installed with the pump pressure pre-set to 145 psi, the turbulator set at 3 and the air gate set to 3. These are general preliminary settings and adjustments should be made to ensure clean combustions for this application.

i.Replace burner cover.

j.The air adjustments can be made by removing the plastic plug on the top right side of the cover. Turning the screw counter clockwise will increase the amount of combustion air. Turning the screw clockwise will decrease the amount of combustion air. A small ¼ “ diameter hole should be drilled in PVC just outside the furnace to insert the combustion sample hose. Remember to seal hole after acquiring flue gas sample.

5.Burner now operates and can be properly set-up for clean combustion.

6.Blower comes on after delay on time.

Notice: To achieve proper combustion instruments must be used to secure CO2 or O2 readings and smoke samples.

Notice: Heat exchanger oil will burn off on initial firing creating an unpleasant odor. To prevent this odor from occurring more than once, it is suggested the heating section be allowed to run for 30 minutes, or until odor has dissipated.

27

Page 29 Page 31
Image 30
Page 29 Page 31
Contents OIL Fired Furnace OHCFA072DV4RContents = Highboy D = Downflow = FrontSafety Section WARNING and CautionsCAUTION do not Attempt to Start the Burner When Page Codes and Clearances Highboy Combustible materialNon-combustible material OHCFA072DV4RII. General Instructions Venting Fig-1 Installation of Ventor Fig-2Fig-3 Page Condensate Drain Line Connections Fig-4Duct WORK/AIR Conditioning Air Filter Mounted External to Furnace Maximum Model Number Filter Type Air Velocity OHCFt/min Limit Position and Location Burner InstallationBurner Specifications and Applications Fig-7BTU/HR OHCFA072DV4R OIL Tank and PipingRiello 75,000 72,000Page Electrical Wiring Electrical ConnectionsRoom Thermostat Post-Purge Timer Electronic Air Cleaner EAC and Humidifier InstallationThermostat Anticipator Setting Blower Motor Speed SelectionOHCFA072DV4 Alterations REQ’D for A/C @ Design External Static PressureTerminal Definitions & Field Wiring Blower Controller Information for ECM MotorInputs Outputs Operating Modes On and OFF Blower Delay Time Switch Settings Trouble Shooting Startup ProceduresDiagnostic Features To Turn Off Oil to Appliance Sequence of Operation for the OHCPage Page Adjustment Of Heat Input Rate Setting Supply Air Temperature RiseCheckout Procedure Inspection Areas Filter Cleaning and LocationIII. Users Information Section  Caution do not Attempt to Make Repairs YourselfIV. Installers Instructions to User Dealer Maintenance Safety During Servicing and Inspection General InspectionHeat Exchanger Cleaning Instructions Page Fig-12 Fig-13 SUPPLY/RETURN AIR Blower Filter maintenance procedureElectrical System SUPPLY/RETURN AIR FilterFilter replacement Extended Appliance ShutdownOn Shutdown On Startup VI. HOMEOWNER/USER Information and Routine Maintenance Fig-16 Page Page Page Page Page Page Customer Appendix a Replacement Parts OHC BF3 Riello Burner Page Appendix B Wiring Diagram

PHCFA072DV4R specifications

The Thermo Products PHCFA072DV4R is a cutting-edge heating and cooling solution designed for modern residential and light commercial applications. This unit stands out due to its efficient performance and advanced technology. One of the most remarkable features of the PHCFA072DV4R is its energy efficiency. It boasts a high SEER rating that ensures reduced energy consumption without sacrificing comfort, making it an environmentally friendly choice for homeowners.

This system utilizes an inverter-driven compressor, which allows for variable speed operation. This means that the unit can adjust its output to match the specific heating or cooling needs of a space, providing more consistent temperatures and enhanced comfort. Additionally, this inverter technology minimizes noise levels, making the PHCFA072DV4R a quieter option compared to traditional fixed-speed systems.

Another noteworthy characteristic of the PHCFA072DV4R is its advanced filtration system. It is equipped with high-efficiency filters that effectively capture dust, pollen, and other airborne particles, ensuring improved indoor air quality. For those who suffer from allergies or have respiratory issues, this feature can provide significant relief.

The unit offers a user-friendly interface with a smart thermostat that enables users to control the system remotely. Through a mobile app, homeowners can adjust settings, set schedules, and monitor energy usage from anywhere, which adds a layer of convenience to the overall user experience.

Additionally, the PHCFA072DV4R is built with durability in mind. Its robust construction and high-quality materials ensure long-term reliability, reducing the likelihood of costly repairs. It also comes with a warranty that reflects the manufacturer's confidence in the product's performance.

Overall, the Thermo Products PHCFA072DV4R encapsulates efficiency, comfort, and advanced technology in a single package. Its ability to adapt to varying conditions, combined with features focused on air quality and ease of use, make it a prime choice for anyone looking for a versatile heating and cooling solution. This unit not only meets the demands of today's consumers but also aligns with sustainable practices, making it an ideal addition to any home or business.
Top Page Image Contents