SPX Cooling Technologies TG MAG15-50 Assembly of top cover 0100 or safety relief valve

Page 61

4.Adjust the thickness of shim (8100) by peeling of the required number of layers.

5.Place shim (8100), support ring (8110) and O-ring (8120) on the pump cover (4000).

6.Place idler (0600) complete with bearing bush on the idler pin.

7.Mount pump cover (4000) on the pump casing (0010).

8.Screw in tap bolts (0040) and tighten them crosswise to fix the pump cover (4000) on the pump casing (0010).

9.In case of a stainless steel pump cover (4000), check if the sealing faces around the idler pin and on pin cover (1000) are not damaged and free of dirt.

10. Use a new gasket (1020) before fixing pin cover

1010

(1000) on the pump cover (4000) with tap bolts

 

(1010). Tighten tap bolts (1010) crosswise with

 

the specified torque.

 

4000

1020

1000

4.3.7Assembly of top cover (0100) or safety relief valve

1.Check that the sealing faces of the pump casing (0010) and on the top cover (0100) or safety relief valve are not damaged and free of dirt.

2.Place a new gasket (1090) on the pump casing (0010).

3.Place top cover (0100) or safety relief valve on the pump casing (0010).

Remark: The position of the top cover (0100) or safety relief valve depends on the sense of rotation. The grooves in the contact face of the top cover (0100) or safety relief valve must connect the hole in the top face of the pump casing (0010) with the suction side of the pump. The sense of rotation is indicated with an arrow on the top cover (0100) or safety relief valve.

4.Screw in tap bolts (1080) and tighten them crosswise with the specified torque (see Chapter 3.21.3.1) to fix the top cover (0100) or safety relief valve on the pump casing (0010).

1080

0100

1090

0010

A.0500.551 – IM-TGMAG/02.00 EN (02/2008)

61

Page 60 Page 62
Image 61
Page 60 Page 62
Contents TopGear MAG EC-Declaration of conformity Contents Installation Rotor bearing assemblyGuidelines for assembly Cleaning the pumpMaintenance instructions Instructions for re-using and disposal 20.1.1Clearance adjustment Designation of threaded connections 20.1.2Pump cover and intermediate cover SS Hydraulic part Bearing bracket Jacket optionsPump cover and intermediate cover TT Pump cover and without jackets on intermediate cover TOCReception, handling and storage GeneralReception HandlingGeneral SafetyPump units InstallationPump unit handling Before commissioning the pump unit Disassembly/assembly of the coupling guardName plate CE Declaration of Conformity Technical conventions Quantity Symbol UnitDifferential pressure = bar Maximum pressure at discharge flange design pressure = barExample Type designationPump family code TG = TopGear Pump range name Jacket options for pump cover 0 Pump cover without jacketsIdler pin materials Idler bush and idler materialsBushes on shaft materials Rotor and shaft materialsOperating principle Pump standard partsSound Safety relief valve Working principleGeneral performance Self-priming operationPressure Main characteristicsSound level Sound level of a pump without driveSound level of the pump unit Jacket options Maximum and minimum allowable temperatureInternals InfluencesOperation under hydrodynamic lubrication conditions Maximum temperature of internalsMaximum torque of pump shaft and rotor material combination Hyd = design constant for each pump sizeAxial and radial clearances Mass moment of inertiaExtra clearances Inner partsMaximum size of solid particles Play between gear teethDiametral clearance on pin / idler bearing Magnetic coupling Components of the magnetic driveMaximum allowable temperature and nominal torque Rotor bearing assemblySamarium Cobalt SmCo 280C Neodymium Iron Boron NdFeB 120 C BelowCirculation pump Materials rotor bearing assemblySealing rings and gaskets Material circulation pump partsSafety relief valve heated spring casing Safety relief valveMaterials Working pressure classMaterials Definition and working principlePressure HeatingSpring ratio Safety relief valve Safety relief valve Relative adjustmentSectional drawings and part lists Single safety relief valveHeated spring casing InstallationOutdoor installation AccessibilityIndoor installation LocationStability DrivesStarting torque Radial load on shaft endShaft rotation Check after connecting whether the shaft can move freelySuction and discharge pipes Forces and momentsIsolating valves PipingSuction piping Self-priming operationStrainer Secondary pipingDrain lines Heating jacketsTransport of pump unit Guidelines for assemblyFoundation pump unit Jacket on pump coverShaft coupling Combustion enginesGuarding of moving parts Check temperature censor on canAlignment tolerances Belt driveCleaning suction line Cleaning the pumpInstructions for start-up Venting and fillingStart-up Checklist Initial start-upAbnormal operation Shut-downTrouble shooting Tion Instructions for re-using and disposal Maintenance instructionsPreparation External cleaning Motor safetyTools Shut-downFluid circuits Specific componentsNuts and bolts Plastic or rubber componentsFront pull-out Clearance adjustmentBack pull-out 0600 8120 8110 8100 4000 0701 0040 0010 Threaded connection Rp example Rp 1/2 Designation of threaded connectionsThreaded connection G example G 1/2 Disassembly of front-pull-out assembly DisassemblyDisassembly of bearing bracket Disassembly of top cover 0100 or safety relief valveTake off top cover 0100 or safety relief valve Removal of bearing bracketDisassembly of outer magnetic rotor Disassembly of pump shaft completeRemoval of ball bearings Disassembly of back-pull-out assembly Disassembly of separation canUn-tighten cap head screws 8460 and remove them Take out O-rings 81308310 8520 8510 8500 8350-D 8400 0701 Assembly of bearing bracket AssemblyTake care not to damage the outer rotor magnet Adjustment of the axial clearance Pre-assembly of the back-pull-outCirculation pump Mount axial bearing 8350-A into the insertAssembly of rotor shaft Axial clearance Assembly of the separation can Assembly of the back-pull-out assembly to the pump casingAssembly of the front-pull-out assembly Assembly of the bearing bracketMount bearing bracket support 1700 to the bearing bracket Measure the distances as indicated on the sketchOn the pump cover 4000 with tap bolts Assembly of top cover 0100 or safety relief valveTighten tap bolts 1010 crosswise with Specified torque TG MAG15-50 to How to order sparesTG MAG185-125 Bearing bracket Hydraulic partJackets on pump cover Jacket optionsJackets on intermediate cover 0220 0200 0310 0250 0240 0300 0320 0230 0210 TG MAG15-50 to 185-125 pumps Dimensional drawingsCast iron Flange connectionsStainless steel Jackets Jackets dimensions Safety relief valvesSingle safety relief valve Dv dk Heated safety relief valveBracket support Weights MassCopyright 2008 SPX Corporate

TG MAG86-100, TG MAG23-65, TG MAG58-80, TG MAG15-50, TG MAG185-125 specifications

SPX Cooling Technologies has established itself as a leader in the design and manufacturing of cooling systems, offering a wide range of products tailored to meet specific industrial and commercial needs. Among its impressive lineup, the TG MAG series stands out, featuring models such as TG MAG185-125, TG MAG23-65, TG MAG86-100, TG MAG58-80, and TG MAG15-50. Each of these models combines innovative technology with robust performance characteristics, making them ideal choices for various applications.

The TG MAG185-125 model is designed for high-capacity cooling requirements, offering exceptional thermal performance while maintaining energy efficiency. Its advanced fan design minimizes noise levels, making it suitable for installations in noise-sensitive areas. Furthermore, the unit benefits from a corrosion-resistant construction, ensuring longevity and reliable operation in diverse environments.

For smaller applications, the TG MAG23-65 provides a compact solution without compromising on performance. This unit features a space-efficient design and utilizes high-efficiency fans that optimize airflow, thereby enhancing overall cooling efficiency. The integrated digital controls allow for precise temperature management, making it easy for operators to monitor and adjust settings as needed.

The TG MAG86-100 model serves as an ideal middle-ground solution, balancing capacity and efficiency. It incorporates state-of-the-art technology, such as variable speed drives, which adjust the fan speed based on cooling demand, resulting in significant energy savings. The design also promotes easy maintenance, with accessible components that facilitate regular servicing and inspections.

For medium-scale needs, the TG MAG58-80 combines durability with performance, featuring a robust frame that can withstand harsh operational conditions. Its efficient heat exchange technology maximizes cooling output while minimizing energy consumption. Moreover, the enhanced airflow system ensures uniform cooling across the entire unit.

Lastly, the TG MAG15-50 is perfect for smaller spaces where cooling requirements are less demanding. Despite its size, this model is equipped with cutting-edge features such as a compact structure and highly efficient cooling mechanisms to ensure effective performance. The easy installation process and low maintenance needs further enhance its appeal.

Overall, the TG MAG series provides a range of innovative cooling solutions tailored to meet diverse industrial requirements, characterized by efficiency, durability, and advanced technology, ensuring optimal performance across all operating conditions.
Top Page Image Contents