Roberts Gorden CRV-B-8, CRV-B-9, CRV-B-12A, CRV-B-6, CRV-B-10, CRV-B-2 Decorative Grille Bracket

Page 32
Cut relief notches for tube and reflector hangers.

CRV-SERIES INSTALLATION, OPERATION AND SERVICE MANUAL

Step 8.6.3 Reflector Side Extension Installation for Decorative Grilles

NOTE: If the decorative grille system is to be installed in an area with

 

considerable air movement, it is recommended that one

 

#8 x 3/8" sheet metal screw be installed per reflector extension to

6" (15 cm) Minimum

prevent it from blowing over.

Allow 6" (15 cm) minimum clearance between burner box and overhead obstructions for service.

Insert screw

here (see note).

A

Description

Part Number

Reflector Side Extension

01370412

 

 

Reflector Side Extension

Distance "A"

Extension

Minimum

Maximum

Part No.

Width

 

 

 

 

2" (4 cm)

6" (15 cm)

01370408

8" (20 cm)

6" (15 cm)

10" (26 cm)

01370412

12" (30 cm)

 

 

 

 

10" (26 cm)

14" (37 cm)

01370416

16" (40 cm)

 

 

 

 

8.7One-Foot Decorative Grille Installation Step 8.7.1 One-Foot Decorative Grille Bracket

In order to maintain reflector shape, do not fasten brackets together.

#8 Sheet Metal Screws Do not fasten bracket to adjoining reflectors. Maintain same slipjoint position as reflectors.

Decorative Grille Bracket

Description

Part Number

Bracket

01363003

 

 

Cut relief notches for supports and hangers.

2" (5 cm) Minimum Bracket Overlap

26

Image 32
Contents CoRayVac Page Roberts GORDON, LLC Page Table of Figures Page Heater Safety Manpower RequirementsInstaller Responsibility Wall TagCorrosive Chemicals National Standards and Applicable CodesMaintain clearances to combustibles at all times for safety Standard Reflector ONE Side ReflectorUniversal SHIELD, Position Foot Deco Grille National Standards and Applicable Codes With Lock Coupling Assembly Tube AdapterMajor Components Aluminum or Stainless Steel Reflector SideAdjustable Indoor Sensor Roberts Gordon UltravacVariable Frequency Drive Roberts GordonStandard Parts List Contents of CRV-Series Burner CartonProtective Grille Design Requirements Assembly Overview HeaterHeater Installation Critical Hanger PlacementTube Installation Coupling and Tube Assembly2 Elbow Installation ± 2 5 cmReflector Installation 1 Reflector Installation with Hole 2 Reflector InstallationScrew Wire Form Reflector Support Strap Burner Installation Burner Combustion Chamber Gasket End VentReflector Joint 1 Reflector Joint Installation Optional Heater AccessoriesTee Installation 2 Reflector Joint Installation 3 Reflector Joint DetailReflector Side Extension .3.1 Bracket Installation 2 Side Reflector InstallationSee Page 5, through Page 5, for positions Barrier Shield2 Frame Shield Installation Decorative Grille Bracket 2 Decorative Grille 3 Joint Piece and Reinforcement4 End Piece and Reflector End Cap 3 Grille Installation Protective Grille Installation 1 Silicone Cap Installation2 Grille End Cap Installation Kg per foot Corayvac Classic Cast-Iron Adapter Pump Installation and Venting 9.1 Pump Installation EP-200 Condensate Valve AssemblyVertical Venting Horizontal VentingUnited States Requirements Canadian RequirementsVertical Venting Configuration EP-100 Horizontal Venting Configurations Horizontal Venting 4 10 cm PipeEP-200 Series Horizontal Venting Configurations EP-300 Series Horizontal Venting Configurations Outside AIR Supply Non-PressurizedPressurized Duct Design RulesOutside Air Blower Internal Wiring Outside Air Blower Internal Wiring DiagramAir Supply Blower Support Non-Pressurized Outside Air Supply GAS Piping Gas Connection with Flexible Gas HoseControl Methods Roberts Gordon System ControlRoberts Gordon Ultravactm Dpst Transformer Relay P/N120 120 Two Zone Operation without Control Panel 60 Hz 12 Vdc 120 Ground 208 230 Burner Internal Wiring Setting the Vacuum Starting the SystemChecking the Gas Line Checking the Electrical SystemVacuum Reading Operation and Maintenance Pre-Season Maintenance and Annual InspectionSequence of Operation To Shut Off HeaterMaintenance Checklist Installation Code and Annual InspectionsVehicles and Other Objects ReflectorTubes Gas LineWindow Blower Scroll, WheelWith the Power off PumpChart StartTroubleshooting Flow Yes Follow burner check Procedure given aboveReplacement Parts DescriptionGeneral Specifications DimensionsPipe Connection GAS Inlet PressurePump Specifications Model EP-100 Air Supply Blower SpecificationsEP-203 EP-303Page Limitations on Authority Representatives Warranty is Void ifROBERTS-GORDON will not PAY for Page Owner Warranty Registration Card Page Page F r a r e d H e a t i n g
Related manuals
Manual 40 pages 12.87 Kb Manual 40 pages 29.7 Kb

CRV-B-4, CRV-B-12, CRV-B-2, CRV-B-10, CRV-B-6 specifications

The Roberts Gordon CRV-B-9 is a state-of-the-art infrared radiant heater designed for industrial and commercial heating applications. Renowned for its efficiency and effectiveness, the CRV-B-9 represents a significant advancement in the world of space heating solutions.

One of the main features of the CRV-B-9 is its advanced infrared technology, which allows for precise heating without the necessity of warming the entire space. This targeted heating provides immediate comfort, as it directly warms objects and people rather than the air around them, making it particularly effective in large warehouses, manufacturing facilities, and retail spaces.

The heater boasts an impressive output of up to 80,000 BTUs, making it suitable for a wide range of applications. It utilizes natural gas as fuel, which contributes to its efficiency and cost-effectiveness. With a robust design and durable construction, the CRV-B-9 is built to withstand the rigors of industrial environments while ensuring a long product lifespan.

Another significant characteristic of the CRV-B-9 is its ability to integrate with advanced control systems. This includes compatibility with programmable thermostats and energy management systems, allowing for optimized temperature control and reduced energy consumption. The heater can be adjusted to suit different operational needs, making it a flexible solution for various heating scenarios.

The CRV-B-9 also features a compact design, allowing for easy installation in a variety of spaces. Its low-profile shape and modular capability enable users to arrange multiple units to achieve the desired heating coverage without compromising floor space, a crucial aspect for busy, high-traffic areas.

Safety is a priority with the CRV-B-9, which is equipped with various safety features such as a flame safety cutoff switch and over-temperature protection. These mechanisms ensure safe operation, providing peace of mind for users in demanding environments.

In summary, the Roberts Gordon CRV-B-9 infrared radiant heater stands out for its innovative technology, impressive output, energy efficiency, and safety features. Its flexibility and robust design make it an ideal choice for businesses looking to enhance comfort while minimizing energy costs. Whether in a manufacturing plant or a retail outlet, the CRV-B-9 provides a reliable and effective heating solution.