Roberts Gorden BH Series service manual Protective Grille Installation, Silicone Cap Installation

Page 29

ROBERTS GOR DON® BH-SERI E S SUBM IT TAL SHE E T

PROTECTIVE GRILLE INSTALLATION

Silicone Cap Installation

	Silicone Cap
Grille	Description	Part Number
Grille	Grille Section	08050001
Finger	Grille Section	08050001
Finger	Grille End Cap	08050002
	Grille End Cap	08050002
	Silicone Cap	91915951-6P

Grille End Cap Installation	B
A	B
Grille	Grille End Cap
C	D
	Bend up 90°
Pull outward

Grille Installation

Reflector

40 "

(101 cm)

Final Grille

Section

Grille

End Cap

APPLICATION S, ENGI NEERING AND DETAI LED GUID ANCE ON SYSTEMS DESIGN, INSTALLATI ON AND PRODUCT PERFORMANCE IS AVAI LABLE UPON REQUEST. ROBERTS GORDON® PRODUCTS ARE TO BE INSTALLED ONLY IN ACCORDANCE WI TH LOCAL LAWS, CODES AND REGULATIONS, AND ONLY BY A CONTRACTOR QUALI FIED I N THE I NSTALLATION AND SERVICE OF GAS-FIRED HEATING EQUI PMENT.

Image 29

Contents Copyright 2004 Roberts-Gordon N170601NA Rev D 07/04 Roberts-Gordon2004 Contents of Core and Extension Packages Standard Parts ListContents of BH-Series Burner Carton General Specifications Standard Reflector Inches Centimeters Model Clearances to CombustiblesOne Side Reflector Inches Centimeters Two Side Reflectors Inches CentimetersInches Centimeters Tilt Reflector Inches CentimetersTube, Full Inches Centimeters Model ModelLower Clearance Shield Inches Centimeters Tube, Opposite 45 Reflector Inches Centimeters ModelBH-80 153 166 BH-40 BH-60 138 150BH-40 Venting InchesVent BH-60 Infrared Tubes Pipes BH-80 BH-100 BH-115/125 BH-140/150 BH-175/200BH-SERIES Assembly Overview BH-Series Linear Assembly Overview Critical Hanger Placement Heater InstallationBH-Series Linear Layout Overview Weld Must be to the bottom of the tube Burner Tube InstallationBurner Tube Hook 91907302 Tube/Reflector Hanger 03090100Coupling and Tube Assembly Tube Clamp Package InstallationOpen ClosedTighten slide bar as shown below Correct Slide DimensionsPosition 229 cm ± 305 25 cm Total Overall Tube LengthHanger Burner Tube Reflector Turbulator InstallationReflector Installation Overlap must be a Minimum of 6 16 cm Reflector, U-Clip and Reflector Support InstallationScrew Reflector SupportExtra chain min 12 30 cm Burner Gasket Lock Burner InstallationHook Burner Tube Bolt Torque 120 Bolt 94273914 BurnerBH-Series U-Tube Assembly Overview Optional Heater AccessoriesTube, Standard Tube, FullBH-Series U-Tube Layout Overviews BH-175 BH-200 BH-140 BH-150 BH-175 BH-200Tube Coupling Elbow Package Configuration Elbow InstallationReflector Joint Installation Attach Reflector Joint Reflector Joint DetailJoint Reflector Side Extension Bracket InstallationSide Reflector Installation Shield Support Strap Assembly Lower Clearance Shield InstallationTWO-FOOT Decorative Grille Installation Grille InstallationShield Frame Shield InstallationReflector Side Extension Installation One-Foot Decorative Grille Bracket ONE-FOOT Decorative Grille InstallationDecorative Grille Joint Piece and ReinforcementElbow End Piece and Reflector End CapReflector joint piece End PieceSilicone Cap Installation Protective Grille InstallationHorizontal Ventilation 4 10 cm Pipe VentingVertical Ventilation 4 10 cm Pipe Combustible or Non-Combustible Wall OnlyTjernlund VH1-6 or Equivalent Common Sidewall VentingOutside Wall Vent Terminal 6 15 cm 90502101Top View Roberts-Gordon Common Vertical VentingVent Cap 4 10 cm 90502300 Vertical Outside Air Supply for Single Heater InstallationOutside Combustion AIR Supply Vent Cap Vertical Outside Air Supply for Double Heater InstallationVent Cap Wall Outside Vent Cap 6 15 cm 90502302Shown without blower assembly Gas Connection with Stainless Steel Flex ConnectorGAS Piping Shut-Off ValveLine Voltage Thermostat Wiring WiringBurners Maximum 5 BurnersSpdt Transformer Relay Low Voltage Thermostat WiringLow Voltage Thermostat BlackBH-Series Ladder Diagram BH-Series Internal WiringBlower Transformer Pressure Switch Gap Electrode Ground Power Sense Spark Valve Ignition Module Gas ValveElectrical Connection to the Burner Pressure Switch Internal Burner DiagramROBERTS-GORDON will not PAY for Warranty is Void ifLimitations on Authority Representatives Canada