HP Pro 6305 manual Computer Operating Guidelines and Routine Care

Page 102

EComputer Operating Guidelines, Routine Care and Shipping Preparation

Computer Operating Guidelines and Routine Care

Follow these guidelines to properly set up and care for the computer and monitor:

Keep the computer away from excessive moisture, direct sunlight, and extremes of heat and cold.

Operate the computer on a sturdy, level surface. Leave a 10.2-cm (4-inch) clearance on all vented sides of the computer and above the monitor to permit the required airflow.

Never restrict the airflow into the computer by blocking any vents or air intakes. Do not place the keyboard, with the keyboard feet down, directly against the front of the desktop unit as this also restricts airflow.

Never operate the computer with the access panel or any of the expansion card slot covers removed.

Do not stack computers on top of each other or place computers so near each other that they are subject to each other’s re-circulated or preheated air.

If the computer is to be operated within a separate enclosure, intake and exhaust ventilation must be provided on the enclosure, and the same operating guidelines listed above will still apply.

Keep liquids away from the computer and keyboard.

Never cover the ventilation slots on the monitor with any type of material.

Install or enable power management functions of the operating system or other software, including sleep states.

Turn off the computer before you do either of the following:

Wipe the exterior of the computer with a soft, damp cloth as needed. Using cleaning products may discolor or damage the finish.

Occasionally clean the air vents on all vented sides of the computer. Lint, dust, and other foreign matter can block the vents and limit the airflow.

94 Appendix E Computer Operating Guidelines, Routine Care and Shipping Preparation

Image 102
Contents Hardware Reference Guide Hardware Reference Guide About This Book Iv About This Book Table of contents Small Form Factor SFF Hardware Upgrades Preventing Electrostatic Damage Grounding Methods Viii Product Features Standard Configuration FeaturesMicrotower MT Front Panel Components 1Front Panel ComponentsSmall Form Factor SFF Front Panel Components 2Front Panel ComponentsMicrotower MT Rear Panel Components 3Rear Panel ComponentsSmall Form Factor SFF Rear Panel Components 4Rear Panel ComponentsMedia Card Reader Components 5Media Card Reader Components6Keyboard Features KeyboardUsing the Windows Logo Key 7Windows Logo Key FunctionsAny number key Serial Number Location 8Microtower Serial Number and Product ID LocationMicrotower MT Hardware Upgrades Serviceability FeaturesRemoving the Computer Access Panel Replacing the Computer Access Panel Removing the Front Bezel Removing Bezel Blanks Replacing the Front BezelSystem Board Connections 1System Board ConnectionsInstalling Additional Memory DIMMsDDR3-SDRAM DIMMs Installing DIMMs Populating Dimm SocketsPage Removing or Installing an Expansion Card Page Page Page Drive Positions 2Drive PositionsInstalling and Removing Drives Media16Extra Guide Screw Locations Removing a 5.25-inch or 3.5-inch Drive from a Drive Bay 19Removing the Drives Microtower MT Hardware Upgrades Installing a 5.25-inch or 3.5-inch Drive into a Drive Bay Page Page Removing a Hard Drive from a Drive Bay Installing a Hard Drive into an Internal Drive Bay Page Page Page Installing a Security Lock Cable LockPadlock HP Business PC Security Lock Page Page Page Front Bezel Security Page Small Form Factor SFF Hardware Upgrades Removing the Computer Access Panel Replacing the Computer Access Panel Removing the Front Bezel 4Removing a Bezel Blank Changing from Desktop to Tower Configuration Black ESATA Adapter Cable Sata Installing Additional Memory Installing DIMMs 8Rotating the Drive Cage Up Installing Additional Memory Page Removing or Installing an Expansion Card Page Page Page 16Drive Positions 17Extra Guide Screw Locations Page Removing a 5.25-inch Drive from a Drive Bay Page Installing a 5.25-inch Drive into a Drive Bay 21Removing the 5.25-inch DrivePage Page Removing a 3.5-inch Drive from a Drive Bay Page Installing a 3.5-inch Drive into a Drive Bay Page Page Page Page Page 40Installing a Cable Lock HP Business PC Security Lock Page Page Page Front Bezel Security Page Battery Replacement Type Page Removing and Replacing a Removable 3.5-inch Sata Hard Drive Page Figure B-5Replacing the Hard Drive Page Page Unlocking the Smart Cover Lock Smart Cover FailSafe KeyPage Page Preventing Electrostatic Damage Grounding MethodsComputer Operating Guidelines and Routine Care Safety Optical Drive PrecautionsCleaning Shipping PreparationIndex Tower conversion
Related manuals
Manual 232 pages 63.47 Kb