York D2EB Installation, Limitations, Unit Application Data, Location, Rigging Or Handling

Page 2
INSTALLATION

PRODUCT NOMENCLATURE

174065-YIM-A-0206

PRODUCT CATEGORY

D = Single Package Air Conditioner (Air Cooled)

PRODUCT GENERATION

2 = 2nd Generation

PRODUCT IDENTIFIER

EB = 10 SEER Cooling Models

D

2

E LIMITATIONS B

0 TABLE 1 - UNIT APPLICATION DATA 2 LOCATIONRIGGING OR HANDLING 4 FIG. 1 - CENTER OF GRAVITYManual background A Manual backgroundManual background 0 Manual background 6

NOMINAL COOLING

CAPACITY (MBH)

018 = 18,000 BTUH

024 = 24,000 BTUH

030 = 30,000 BTUH

036 = 36,000 BTUH

042 = 42,000 BTUH

048 = 48,000 BTUH

060 = 60,000 BTUH

VOLTAGE CODE

06 = 208/230-1-60

FACTORY

INSTALLED ELECTRIC HEAT

A = No Electric Heat Installed

INSTALLATION

LIMITATIONS

These units must be installed in accordance with the following national and local safety codes.

1.National Electrical Code ANSI/NFPS No. 70 or Canadian Electrical Code Part 1, C22.1 (latest editions).

2.Local plumbing and waste water codes and other applica- ble local codes.

Refer to Table 1 for unit application data and to Table 5 for elec- tric heat application data.

If components are to be added to a unit to meet local codes, they are to be installed at the dealer's and/or the customer's expense.

Size of unit for proposed installation should be based on heat loss/heat gain calculations made in accordance with industry recognized procedures identified by the Air Conditioning Con- tractors of America.

TABLE 1 - UNIT APPLICATION DATA

Voltage Variation

 

208/230V

3

187 / 253

3

Min. / Max.1

 

 

 

Wet Bulb Temperature (°F) of Air on

 

57 / 72

 

Evaporator Coil,

Min. / Max.

 

 

 

 

 

Dry Bulb Temperature (°F) of Air on

 

45 / 120

 

Condenser Coil,

Min.2 / Max.

 

 

Rated in accordance with ARI Standard 110, utilization range “A”.

￿A low ambient accessory is available for operation down to 0°F

“T1" transformer primary tap must be moved from the 230 volt connection to the 208 volt connection for low voltage applications of 208 volt and below.

LOCATION

Use the following guidelines to select a suitable location for these units.

1.Unit is designed for outdoor installation only.

2.Condenser must have an unlimited supply of air. Where a choice of location is possible, position unit on either north or east side of building.

3.For ground level installation, a level pad or slab should be used. The thickness and size of the pad or slab used should meet local codes and unit weight. Do not tie the slab to the building foundation.

4.For roof top installation, be sure the structure will support the weight of the unit plus any field installed components. Unit must be installed on a level roof curb or appropriate an-

gle iron frame providing adequate support under the compressor/condenser section.

5. Maintain level tolerance of unit to 1/8" maximum.

RIGGING OR HANDLING

Care must be exercised when moving the unit. Do not remove any packaging until the unit is near the place of installation. Rig unit with slings placed under the unit. Spreader bars of suffi- cient length should be used across the top of the unit.

BEFORE LIFTING A UNIT, MAKE SURE THAT ITS WEIGHT IS DISTRIBUTED EQUALLY ON THE CABLES SO THAT IT WILL LIFT EVENLY.

Units may also be moved or lifted with a fork-lift. Slotted open- ings in the skid are provided for this purpose. Forks must pass completely through the base.

Refer to Table 2 for unit weights and to Figure 1 for approximate center of gravity.

TABLE 2 - UNITS WEIGHTS

 

SHIPPING

OPERAT-

CORNER WEIGHTS

 

UNIT

ING

 

(location, lbs.)

 

WEIGHT

 

 

SIZE

WEIGHT

 

 

 

 

(lbs.)

 

 

 

 

 

(lbs.)

“A”

“B”

“C”

“D”

 

 

018

318

313

86

76

73

83

024

324

319

88

77

75

85

030

333

328

85

81

82

86

036

338

333

91

80

78

88

042

347

342

94

83

80

91

048

368

363

92

88

92

97

060

376

371

105

100

84

87

 

 

“D”

 

 

 

 

 

 

 

 

CENTER OF GRAVITY

FRONT

 

“A”

 

“C”

 

 

OF

 

 

 

 

 

 

 

 

 

 

 

UNIT

 

“B”

 

 

 

 

 

 

 

 

 

 

 

49 ￿￿

26

 

 

47 ￿￿

 

FIG. 1 - CENTER OF GRAVITY

2

Unitary Products Group

Image 2
Contents GENERAL INSTALLATION INSTRUCTIONREPLACEMENT PARTS REFERENCETABLE 1 - UNIT APPLICATION DATA INSTALLATIONLIMITATIONS LOCATIONDUCT WORK SERVICE ACCESSCLEARANCES FILTERSCONTROL WIRING POWER AND CONTROL WIRINGFIG. 2 - TYPICAL FIELD WIRING DIAGRAM POWER WIRINGTABLE 4 - ELECTRICAL DATA BASIC UNIT TABLE 5 - ELECTRICAL DATA COOLING / ELECTRIC HEAT Checking Supply Air CFM DEB Coil Delta P vs Airflow174065-YIM-A-0206 174065-YIM-A-0206 FRONT FIG. 3 - DIMENSIONS AND CLEARANCESFRONT 14 BACKHeating SEQUENCE OF OPERATIONCooling MAINTENANCE NORMAL MAINTENANCEDETAIL A SEE DETAIL B174065-YIM-A-0206 TYPICAL WIRING DIAGRAM LEGENDTYPICAL WIRING DIAGRAM NOTES Unitary Products Group174065-YIM-A-0206 Unitary Products GroupSupersedes Nothing Unitary Products Group5005 York Drive, Norman Oklahoma 174065-YIM-A-0206