HP 2995 manual Product Specifications, Electrical Ratings

Page 4

PRODUCT SPECIFICATIONS

ABOUT THIS PRODUCT - Bodine’s PACESETTERTM “NEMA 4” series inverter is designed to provide variable speed control of standard three- phase AC induction motors. Adjustable linear acceleration and deceleration are provided, making the drive suitable for soft start applications. The output voltage is sinewave coded PWM operating at 16 kHz, which provides high motor torque, high efficiency, and low noise. The full featured drive is easy to install and operate. Simple trimpot adjustments eliminate the computer-like programming required on other drives. However, for most applications, no adjustments are necessary.

Table 1 – Electrical Ratings

 

 

 

 

Input Volts

115 or 230 VAC +/- 10%, Single Phase, 50/60Hz

Input Current

 

11.0 (115V) or 7.0 (230V) Amps AC

Output Volts

 

0 – 230 VAC, Three Phase

 

Output Current, per Phase

 

2.4 Amps RMS

 

Maximum Motor HP (kW)

 

½ HP (0.37 kW)

 

Table 2 - General Performance Specifications

 

Parameter

 

 

Specification

 

Factory

 

 

 

 

 

Setting

Maximum Load

 

150%

Current Overload for 2 Minutes

 

-

Switching Frequency at Motor

 

 

16 kHz

 

-

Signal Following Input Voltage

 

 

0 – 5 VDC

 

-

Signal Following Input Resolution

 

 

8 bits

 

-

Minimum Speed Trimpot Range

 

0 – 40% of frequency setting

 

0

Output Frequency Setting

 

50 Hz, 60 Hz, or 120 Hz

 

60

Maximum Speed Trimpot Range

 

70 – 110% of frequency setting

 

100

Speed Range

 

50:1

 

-

Acceleration Trimpot Range

 

 

.3 – 20 seconds

 

1.0

Deceleration Trimpot Range

 

 

.3 – 20 seconds

 

1.0

Boost Trimpot Range (50Hz only)

 

 

6 – 30%

 

-

Slip Compensation Trimpot

 

 

0 – 3 Volts/Hz/Amp

 

1.5

Range

 

 

 

 

 

Current Limit Trimpot Range

 

 

1.5 – 4.5 Amps AC

 

3.8

Speed Regulation (0 to Full Load,

 

 

2.5% of Base Speed

 

-

30:1 Speed Range)

 

 

 

 

 

Operating Temperature Range

 

 

0 to +40OC

 

-

Overload Protector Trip Time

 

 

6 seconds

 

-

(Stalled Motor)

 

 

 

 

 

Bus Overvoltage Trip Point

 

400 VDC (283 VAC Line Volts)

 

 

Bus Undervoltage Trip Point

 

260 VDC (184 VAC Line Volts)

 

 

4

Image 4
Contents Phase AC Motor Speed Control Quick Reference Table of Contents Product Specifications Electrical RatingsImportant Safety Precautions Installation Examine before installationChoose a Suitable Location Mount ControlPreliminary Setup ConnectionPage Connect the Motor Electrical connections for ModelConnect AC Line Cord Connect to AC PowerClose and Seal the Enclosure Operation Check System Before StartingAdjust Trim Pots Optional Operate the InverterMIN Minimum Speed DEC/B Deceleration with 60 Hz or 120 Hz configuration CL Current Limit with I2t Shutdown Troubleshooting Abnormality Check Point CountermeasureOperating LED LED Flash Corrective Declaration of Conformity Type HPP-5337E4 AC Motor Speed Control, Model numberBodine Limited Warranty