HP C4599, C4580 manual Connect to additional computers on a network, To connect the product

Page 9

To connect the product

1.Insert the product software CD in the computer CD-ROM drive.

2.Follow the instructions on the screen.

When you are prompted, connect the product to the computer using the USB setup cable included in the box. The product will attempt to connect to the network. If the connection fails, follow the prompts to correct the problem, and then try again.

3.When the setup is finished, you will be prompted to disconnect the USB cable and test the wireless network connection. Once the product connects successfully to the network, install the software on each computer that will use the product over the network.

Connect to additional computers on a network

You can connect the HP All-in-One to a small number of computers on a network. If the HP All-in-One is already connected to a computer on a network, for each additional computer you must install the HP All-in-One software. During installation of a wireless connection, the software will discover the product on the network. Once you have set up the HP All-in-One on the network you will not need to configure it again when you add additional computers.

To install the Windows HP All-in-One software on additional networked computers

1.Quit all applications running on your computer, including any virus detection software.

2.Insert the Windows CD that came with the HP All-in-One into the CD-ROM drive on your computer and follow the onscreen instructions.

3.If a dialog box about firewalls appears, follow the instructions. If you see firewall pop- up messages, you must always accept or allow the pop-up messages.

4.On the Connection Type screen, select Through the network, and then click Next.

The Searching screen appears as the Setup program searches for the HP All-in-One on the network.

5.On the Printer Found screen, verify that the printer description is correct.

If more than one printer is found on the network, the Printers Found screen appears. Select the HP All-in-One you want to connect.

6.Follow the prompts to install the software.

When you have finished installing the software, the HP All-in-One is ready for use.

7.If you disabled any virus detection software on your computer, make sure to enable it again.

8.To test your network connection, go to your computer and print a test page to the HP All-in-One.

Network setup

Change the HP All-in-One from a USB connection to a network connection

If you first install the HP All-in-One with a USB connection, you can later change to a wireless network connection. If you already understand how to connect to a network, you can use the general directions below.

Change the HP All-in-One from a USB connection to a network connection

7

Page 8 Page 10
Image 9
Page 8 Page 10
Contents Basics Guide Hewlett-Packard Company notices Contents If you want to Network setupConnect to an integrated wireless Wlan 802.11 network What you need for an integrated wireless Wlan 802.11 networkTo connect the product Wireless ad hoc network setupWhat you need for an ad hoc network Connect to a wireless ad hoc network Communication mode Ad Hoc Encryption enabledCreate a network profile for other operating systems Connect to additional computers on a network Configure your firewall to work with HP products Print network settings Manage your network settingsRestore network defaults Advanced firewall informationPrint the wireless network test Turn the wireless radio on and offHP All-in-One at a glance HP All-in-One overviewOne overview Control panel featuresLoad paper Find more informationStart Here guide Onscreen HelpTo load small-size photo paper in the input tray To load full-size paperPrint a photo on photo paper Avoid paper jamsScan an image To print photosTo scan to a computer To replace the print cartridges Replace the print cartridgesOne overview HP All-in-One overview Uninstall and reinstall the software Troubleshooting and supportTroubleshooting common setup issues To uninstall and reinstall the softwareSetup troubleshooting Solution 1 Press the On button to turn on the product After setting up the product, it does not printSolution 2 Set your product as the default printer Solution 5 Load paper in the input trayThis prints the Wireless Network Test Network troubleshootingTo run the Network Diagnostic tool To check a wired Ethernet connectionTo print the Network Configuration To check a wireless connectionThis prints the Network Configuration Make sure the product is on the networkTo access the HP Photosmart C4500 All-in-One series home Make sure the HP Network Devices Support service is runningTo restart the HP Network Device Support service Make sure the product is online and readyIf you have a problem, follow these steps Print cartridge troubleshootingClear paper jams Support processTechnical information Product specificationsSystem requirements Regulatory noticesHP product Duration of limited warranty WarrantyXHPERXUJ UDQDLV
Related manuals
Manual 12 pages 60.99 Kb Manual 261 pages 11.49 Kb
Top Page Image Contents