United States Stove ASA7 Heater Installation, Minimum Clearances to Combustible Wall and Ceilings

Page 12

HEATER INSTALLATION

CAUTION: FOR YOUR SAFETY, THE INSTALLATION OF THIS HEATER MUST COMPLY WITH LOCAL CODES AND REGULATIONS. CONTACT LOCAL BUILDING OR FIRE OFFICIALS ABOUT INSPECTION TO ASSURE PROPER COMPLIANCE WITH LOCAL CODES AND REGULATIONS.

MINIMUM CLEARANCES TO COMBUSTIBLE WALL AND CEILINGS

CAUTION: MOST WALLS AND CEILINGS CONTAIN WOOD EVEN THOUGH THEY ARE MADE OF SHEETROCK OR PLASTER ON THE OUTSIDE. THESE WALLS AND CEILINGS CAN CATCH FIRE FROMTHE HOT WATER HEATER OR CHIMNEY CONNECTOR IF HEATER AND CHIMNEY CONNECTOR ARE NOT PROPERLY INSTALLED.

Minimum clearances to unprotected combustible walls and ceilings as noted by Figure 8 must be maintained. Drapes, curtains, furniture and other combustible materials should be kept much further away from the heater chimney connector to avoid a fire.

CEILING

CEILING

 

 

 

32

 

 

21

 

BACK WALL

 

 

21

 

17

17

21

32

 

 

WALL

WALL

 

SIDE WALL

 

WALL

BACK

BACK

 

 

32

 

 

 

 

32

 

FIGURE 8 -

 

 

 

MINIMUM CLEARANCES TO COMBUSTIBLE MATERIALS (IN INCHES)

 

 

 

 

 

CORNER

 

 

 

INSTALLATION

f you choose to, you may install the heater and chimney connector closer to combustible surfaces than indicated by Figures 2 through 4 IF a clearance reduction system is also installed to protect combustible ceilings and walls near the heater and chimney connector. However, there are limits to how close the heater and chimney connector can be installed to combustible surfaces protected by a clearance reduction system.

A correctly installed clearance reduction system protects the combustible surfaces well beyond the sides and above the top of the heater and beyond the sides and top of the chimney connector pipe.

Two common types of clearance reduction systems use sheet metal with a minimum thickness of 28 gauge (galvanized steel, aluminum, copper) or a 3-1/2 inch (4 inch nominal) thick masonry wall. Either of these materials must be spaced out 1 inch from the combustible surfaces. With sheet metal, non-combustible spacers are used to maintain the 1 inch air space. With a masonry wall, metal wall ties and furring strips, if needed are used to anchor the brick to the wall. To avoid excessive heat transmission, the spacers or wall ties should not be placed directly behind the heater or chimney connector. The 1 inch air space provides free air circulation. It is essential that there be openings at the top and bottom of these clearance reducers so cool air can enter at the bottom and hot air exit at the top. It is the "chimney effect" whereby when the air in the space is heated, it rises exiting from the top and being replaced by cooler air at the bottom, that makes these shields effective.

12

USSC

Image 12
Contents Owner’s Manual Safety Precautions Safety Standards and Building CodesMaterials Needed for Proper Installation Assembly Shaker Handle AssemblyFlue Collar Assembly Feed & Ash Door AssembliesMasonry Chimney RequirementsMasonry Chimney Requirements Masonry Chimney Requirements Chimney Height RequirementsOn Next Contiued on Next Part B Contin Metal Prefabricated Chimney Installation Metal Prefabricated Chimney RequirementsDetail Connection Detail Connection Heater Installation Minimum Clearances to Combustible Wall and CeilingsMinimum Clearances to Combustible Materials in Inches To Install the Heater When Chimney Connector Exits Through the CeilingInstallation of Chimney Shield Operating Instructions Burning Coal in your 4027/ASA7Loading Increasing Heat From a Low FireShaking Draft ControlsSafety ASA7 Model 4027 & ASA7 Parts List HOW to Order Repair Parts