ASRock 970 Extreme4 manual For Windows VistaTM / VistaTM 64-bit / 7 / 7 64-bit OS

Page 22

For Windows® VistaTM / VistaTM 64-bit / 7 / 7 64-bit OS:

A. Click the Start icon on your Windows taskbar.

B. From the pop-up menu, select All Programs, and then click NVIDIA Corporation.

C. Select NVIDIA Control Panel tab.

D. Select Control Panel tab.

E. From the pop-up menu, select Set SLI and PhysX conﬁguration. In Set PhysX GPU acceleration item, please select Enabled. In Select an SLI conﬁguration item, please select Enable SLI. And click Apply.

F. Reboot your system.

G.You can freely enjoy the benef t of SLITM feature.

*SLITM appearing here is a registered trademark of NVIDIA® Technologies Inc., and is used only for identif cation or explanation and to the owners’ benef t, without intent to infringe.

22

Image 22

Contents Extreme4 Copyright Notice DisclaimerContents CPU Conf guration Install Operating SystemUefi Menu Bar Super IO Conf guration Acpi Conf guration USB Conf gurationPackage Contents IntroductionSpecifications Bios Feature ConnectorSmart Switch Rear Panel I/OHardware Unique FeatureSupport CD MonitorPage Page Page Motherboard Layout SocketLAN Port LED Indications I/O PanelTable for Audio Output Connection Pri Installation Pre-installation PrecautionsInstallation of CPU Fan and Heatsink CPU InstallationTo indicate that it is locked Dual Channel Memory Conﬁgurations Installation of Memory Modules DimmBlue Slot Installing a Dimm Expansion Slots PCI and PCI Express Slots Installing an expansion cardPcie Slots Slitm Operation Guide RequirementsDouble-click Nvidia Settings icon on your Windows taskbar Driver Installation and SetupFor Windows XP / XP 64-bit OS Select Nvidia Control Panel tab For Windows VistaTM / VistaTM 64-bit / 7 / 7 64-bit OSSelect Control Panel tab Page CrossFire Bridge Installing Three CrossFireXTM-Ready Graphics Cards CrossFireTM Bridge For Windows XP OS Install the required drivers to your systemFor Windows 7 / VistaTM OS Surround Display Feature \ Surround Display InformationASRock Smart Remote Installation Guide CIR sensors in different anglesJumper Setting Jumpers SetupClear Cmos Jumper USB 2.0 Headers Onboard Headers and ConnectorsSerial ATA3 Connectors Are three USB 2.0 headers onOne USB 3.0 header on this USB 3.0 Header Besides two default USBOptional wireless transmitting Motherboard. This USBSeveral system front panel System Panel HeaderFunctions Indicate system power status Power LED Header Please connect the chassisPower LED to this header to Power offATX 12V Power Connector ATX Power Connector Please connect an ATX powerSupply to this connector Ieee 1394 Header Besides one default IeeeSmart Switches 12 Dr. Debug Status Code DescriptionPage Page Page What is Hot Swap Function? Serial ATA3 SATA3 Hard Disks InstallationWhat is Hot Plug Function? Hot Plug and Hot Swap Functions for SATA3 HDDsSATA3 HDD Hot Plug Feature and Operation Guide Points of attention, before you process the Hot PlugHow to Hot Plug a SATA3 HDD Installing Windows XP / XP 64-bit With RAID Functions Driver Installation GuideSet up Uefi Use RAID Installation Guide to set RAID conﬁguration \ RAID Installation GuideInstalling Windows XP / XP 64-bit Without RAID Functions Untied Overclocking Technology Uefi Menu Bar IntroductionOperating System To jump to the Exit Screen or exit the current screen Navigation KeysMain Screen System Time HourMinuteSecondOC Tweaker Screen HT Bus Speed Dram Timing Control Power Down EnableMultiplier/Voltage Change HT Bus WidthWrite Recovery Time tWR RAS# to CAS# Delay tRCDCommand Rate CR RAS to RAS Delay tRRDHT Voltage Would you like to save current setting user defaults?NB Voltage CPU Vdda VoltageAdvanced Screen Instant FlashSecure Virtual Machine CPU ConfigurationCool ‘n’ Quiet Enhance Halt State C1ENorth Bridge Configuration Primary Graphics AdapterSouth Bridge Configuration Sata IDE Combined Mode Storage ConfigurationSata Mode Sata ControllerSerial Port Address Super IO ConfigurationSerial Port Infrared PortAcpi Configuration USB Mouse Power On Acpi Hpet tableUSB 3.0 Controller USB ConfigurationUSB 2.0 Controller Legacy USB SupportChassis Fan 2 Setting CPU Fan 1 & 2 SettingChassis Fan 1 Setting Chassis Fan 3 SettingBoot Screen Security Screen Exit Screen Running The Support CD Install Operating SystemSupport CD Information Drivers MenuInstalling OS on a HDD Larger Than 2TB