ASRock 970 Extreme4 manual Hardware Health Event Monitoring Screen, CPU Fan 1 & 2 Setting

Page 63

3.5 Hardware Health Event Monitoring Screen

In this section, it allows you to monitor the status of the hardware on your system, including the parameters of the CPU temperature, motherboard temperature, CPU fan speed, chassis fan speed, and the critical voltage.

CPU Fan 1 & 2 Setting

This allows you to set the CPU fan 1 & 2 speed. Conf guration options: [Full On] and [Automatic Mode]. The default is value [Full On].

Chassis Fan 1 Setting

This allows you to set the chassis fan 1 speed. Conf guration options: [Full On], [Manual Mode] and [Automatic Mode]. The default is value [Full On].

Chassis Fan 2 Setting

This allows you to set the chassis fan 2 speed. Conf guration options: [Full On] and [Manual Mode]. The default is value [Full On].

Chassis Fan 3 Setting

This allows you to set the chassis fan 3 speed. Conf guration options: [Full On] and [Manual Mode]. The default is value [Full On].

63

Image 63
Contents Extreme4 Disclaimer Copyright NoticeContents Super IO Conf guration Acpi Conf guration USB Conf guration Install Operating SystemUefi Menu Bar CPU Conf gurationIntroduction Package ContentsSpecifications Rear Panel I/O ConnectorSmart Switch Bios FeatureMonitor Unique FeatureSupport CD HardwarePage Page Page Socket Motherboard LayoutI/O Panel LAN Port LED IndicationsTable for Audio Output Connection Pri Pre-installation Precautions InstallationCPU Installation Installation of CPU Fan and HeatsinkTo indicate that it is locked Installation of Memory Modules Dimm Dual Channel Memory ConfigurationsBlue Slot Installing a Dimm Installing an expansion card Expansion Slots PCI and PCI Express SlotsPcie Slots Requirements Slitm Operation GuideDriver Installation and Setup Double-click Nvidia Settings icon on your Windows taskbarFor Windows XP / XP 64-bit OS For Windows VistaTM / VistaTM 64-bit / 7 / 7 64-bit OS Select Nvidia Control Panel tabSelect Control Panel tab Page CrossFire Bridge Installing Three CrossFireXTM-Ready Graphics Cards CrossFireTM Bridge Install the required drivers to your system For Windows XP OSFor Windows 7 / VistaTM OS \ Surround Display Information Surround Display FeatureCIR sensors in different angles ASRock Smart Remote Installation GuideJumpers Setup Jumper SettingClear Cmos Jumper Are three USB 2.0 headers on Onboard Headers and ConnectorsSerial ATA3 Connectors USB 2.0 HeadersMotherboard. This USB USB 3.0 Header Besides two default USBOptional wireless transmitting One USB 3.0 header on thisSystem Panel Header Several system front panelFunctions Power off Power LED Header Please connect the chassisPower LED to this header to Indicate system power statusIeee 1394 Header Besides one default Ieee ATX Power Connector Please connect an ATX powerSupply to this connector ATX 12V Power ConnectorSmart Switches Status Code Description 12 Dr. DebugPage Page Page Hot Plug and Hot Swap Functions for SATA3 HDDs Serial ATA3 SATA3 Hard Disks InstallationWhat is Hot Plug Function? What is Hot Swap Function?Points of attention, before you process the Hot Plug SATA3 HDD Hot Plug Feature and Operation GuideHow to Hot Plug a SATA3 HDD Driver Installation Guide Installing Windows XP / XP 64-bit With RAID FunctionsSet up Uefi \ RAID Installation Guide Use RAID Installation Guide to set RAID configurationInstalling Windows XP / XP 64-bit Without RAID Functions Untied Overclocking Technology Introduction Uefi Menu BarOperating System System Time HourMinuteSecond Navigation KeysMain Screen To jump to the Exit Screen or exit the current screenOC Tweaker Screen HT Bus Width Dram Timing Control Power Down EnableMultiplier/Voltage Change HT Bus SpeedRAS to RAS Delay tRRD RAS# to CAS# Delay tRCDCommand Rate CR Write Recovery Time tWRCPU Vdda Voltage Would you like to save current setting user defaults?NB Voltage HT VoltageInstant Flash Advanced ScreenEnhance Halt State C1E CPU ConfigurationCool ‘n’ Quiet Secure Virtual MachinePrimary Graphics Adapter North Bridge ConfigurationSouth Bridge Configuration Sata Controller Storage ConfigurationSata Mode Sata IDE Combined ModeInfrared Port Super IO ConfigurationSerial Port Serial Port AddressAcpi Configuration Acpi Hpet table USB Mouse Power OnLegacy USB Support USB ConfigurationUSB 2.0 Controller USB 3.0 ControllerChassis Fan 3 Setting CPU Fan 1 & 2 SettingChassis Fan 1 Setting Chassis Fan 2 SettingBoot Screen Security Screen Exit Screen Drivers Menu Install Operating SystemSupport CD Information Running The Support CDInstalling OS on a HDD Larger Than 2TB