Pioneer VSX-91TXH manual Controlling the rest of your system, Resetting the remote control presets

11Controlling the rest of your system

•The remote controls should be 3 cm to 5 cm (1 to 2 inches) apart.

3 cm to 5 cm (1 to 2 inches)

RECEIVER

5Press the corresponding button on the other remote control that is sending (teaching) the signal to this receiver’s remote control.

For example, if you want to learn the playback control signal, press and hold  briefly. The LCD display will show OK if the operation has been learned.1

If for some reasons the operation hasn’t been learned the LCD will display ERROR briefly and then display PRES KEY again. If this happens, keep pressing the (teaching) button as you vary the distance between the two remotes,

until the LCD display shows OK.2

Certain buttons represent operations that cannot be

learned from other remote controls.3 The buttons available are shown below (with the exception of the TV controls, a combination of SHIFT and these buttons can also be learned):

RECEIVER	INPUT		SYSTEM OFF
			SOURCE
	SELECT
					TV CONTROL
				TVVOL	INPUT	TVCH	VOL
XM RADIO	SIRIUS	DVR 2			SELECT
DVD	TV	DVR 1	TVCTRL
CD-R/TAPE	HDMI 2	CD	ZONE 2	ANT	REC	INFO
iPod	HDMI 1	TUNER	RECEIVER				MUTE
				MPX		REC STOP	JUKEBOX
	SLEEP	S.RETRIEVER	ANALOG
			ATT
	SR+	DIMMER	MIDNIGHT/	AUDIO	SUBTITLE	HDD	DVD
				DISP		CH	CH
			LOUDNESS
					PHOTO		STEREO/
				STATUS	SIGNAL SEL	SBch
	DIALOG E						F.S.SURR
D.ACCESS +10			CLASS DISC	MULTI OPE	THX	STANDARD	ADV.SURR
			ENTER
AVPARAMETER			CHLEVEL	SHIFT	PHASE	MCACC	S.DIRECT
TOPMENU			MENU
	TUNE
	ST	ST	T.EDIT
SETUP	ENTER		RETURN

	RECEIVER
	TUNE
GUIDE	BAND

Erasing one of the remote control button settings

This erases one of the buttons you have programmed and restores the button to the factory default.

1While pressing the RECEIVER button, press SETUP. The remote LCD display shows SETUP.

2Use / to select ERASE then press ENTER.

The LCD on the remote prompts you for the component corresponding to the button setting to be erased.

3Press the input source button corresponding to the command to be erased then press ENTER.

The LCD display flashes PRES KEY.

4Press and hold the button to be erased for two seconds.

The LCD display shows OK or NO CODE to confirm the button has been erased.

5Repeat step 4 to erase other buttons.

6Press and hold the RECEIVER button for a couple of seconds when you’re done.

Resetting the remote control presets

This will erase all preset remote control preset codes and programmed buttons.

1While pressing the RECEIVER button, press SETUP. The remote LCD display shows SETUP.

2Use / to select RESET then press ENTER. RESET flashes in the LCD display.

3Press and hold ENTER for about two seconds. The LCD shows OK to confirm the remote presets have been erased.

Confirming preset codes

6To program additional signals for the current component repeat steps 4 and 5.

To program signals for another component, exit and repeat steps 1 through 5.

7Press and hold the RECEIVER button for a couple of seconds to exit and store the operation(s).

Use this feature to check which preset code is assigned to an input source button.

1While pressing the RECEIVER button, press SETUP. The remote LCD display shows SETUP.

2Use / to select READ ID then press ENTER.

The LCD on the remote prompts you for the input source button you want to check.

Note

1Note that interference from TVs or other devices will sometimes result in the remote control learning the wrong signal.

2• Some commands from other remote controls cannot be learned, but in most cases the remotes just need to be moved closer together or farther apart.

•If the remote LCD shows FULL, it means the memory is full. See Erasing one of the remote control button settings below to erase a programmed button you’re not using to free up more memory (note that some signals may take more memory than others).

3Note that the number key decimal button (+10/D.ACCESS) may not be learned with some components.

68

En