ASRock 2Core1066-2.13G manual USB Configuration

Page 37

Parallel Port Address

Use this item to set the address for the onboard parallel port or disable it. Configuration options: [Disabled], [378], and [278].

Parallel Port Mode

Use this item to set the operation mode of the parallel port. The default value is [ECP+EPP]. If this option is set to [ECP+EPP], it will show the EPP version in the following item, “EPP Version”. Configuration options: [Normal], [Bi-Directional], and [ECP+EPP].

EPP Version

Use this item to set the EPP version. Configuration options: [1.9] and [1.7].

ECP Mode DMA Channel

Use this item to set the ECP mode DMA channel. Configuration options: [DMA0], [DMA1], and [DMA3].

Parallel Port IRQ

Use this item to set the IRQ for the parallel port. Configuration options: [IRQ5] and [IRQ7].

3.3.8 USB Configuration

 

BIOS SETUP UTILITY

 

 

Advanced

 

 

 

USB Configuration

 

To enable or disable

 

 

the onboard USB

USB Controller

[Enabled]

controllers.

 

 

USB 2.0 Support

[Enabled]

 

 

Legacy USB Support

[Disabled]

 

 

 

 

 

Select Screen

 

 

 

Select Item

 

 

+-

Change Option

 

 

F1

General Help

 

 

F9

Load Defaults

 

 

F10

Save and Exit

 

 

ESC

Exit

v02.54 (C) Copyright 1985-2005, American Megatrends, Inc.

USB Controller

Use this item to enable or disable the use of USB controller.

USB 2.0 Support

Use this item to enable or disable the USB 2.0 support.

Legacy USB Support

Use this item to enable or disable the support to emulate legacy I/O devices such as mouse, keyboard,... etc. Or you may select [Auto] so that the system will start to auto-detect; if there is no USB device connected, “Auto” option will disable the legacy USB support.

3 7

Image 37
Contents 2Core1066-2.13G Disclaimer Copyright NoticeContents Software Support Introduction Package ContentsSpecifications Bios Feature ConnectorSee Caution Support CDDDRII533*, DDRII667 VGA 22.9cm 9.0 Motherboard LayoutTable for Audio Output Connection HD 8CH I/OScrew Holes Pre-installation PrecautionsCPU Installation Land CPU Installation of CPU Fan and Heatsink Installing a Dimm Installation of Memory Modules DimmExpansion Slots PCI, Hdmr and PCI Express Slots Installing an expansion cardPS2USBPWR1 Jumpers SetupIDE1 Onboard Headers and ConnectorsUSB 2.0 Headers Chassis Speaker Header Serial port Header Western Digital Sataii Hard Disk Setup GuideHdmr Card and Driver Installation Driver Installation GuideUntied Overclocking Technology Bios Menu Bar Main Screen Navigation KeysAdvanced Screen CPU Configuration Max Cpuid Value Limit Enhance Halt StateCPU Thermal Throttling No-Excute Memory ProtectionChipset Configuration Dvmt Mode Select Internal Graphics Mode SelectDram RAS# Precharge Dram RAS# Activate to PrechargeCD-In Front PanelOnBoard Lan PCI Fix FunctionAcpi Configuration ATA/IDE Configuration IDE ConfigurationIDE Device Configuration ATA/IDE Configuration EnhancedPIO Mode LBA/Large ModeDMA Mode Block Multi-Sector TransferPCI Latency Timer PCIPnP ConfigurationA.R.T Bit Data TransferSuper IO Configuration Floppy ConfigurationOnBoard Floppy Controller Serial Port AddressUSB Configuration Hardware Health Event Monitoring Screen Target CPU Temperature CCPU Quiet Fan Tolerance CBoot Settings Configuration Boot ScreenBoot From Onboard LAN Boot Up Num-LockChange Supervisor Password Main Advanced Monitor BootSecurity Screen Exit Screen Load Optimal DefaultsSave Changes and Exit Discard Changes and ExitSupport CD Information Install Operating SystemRunning The Support CD Drivers Menu