ASRock CONROE945 manual Floppy Configuration, Super IO Configuration, OnBoard Floppy Controller

Page 36

3.3.6 Floppy Configuration

In this section, you may configure the type of your floppy drive.

 

BIOS SETUP UTILITY

 

 

Advanced

 

 

 

Floppy Configuration

 

Select the type of

 

 

floppy drive

Floppy A

[1.44 MB 312"]

connected to the

 

 

system.

 

 

 

Select Screen

 

 

 

Select Item

 

 

+-

Change Option

 

 

F1

General Help

 

 

F9

Load Defaults

 

 

F10

Save and Exit

 

 

ESC

Exit

v02.54 (C) Copyright 1985-2005, American Megatrends, Inc.

3.3.7 Super IO Configuration

BIOS SETUP UTILITY

 

 

Advanced

 

 

 

Configure Win627EHF Super IO Chipset

Allow BIOS to Enable

 

 

or Disable Floppy

OnBoard Floppy Controller

[Enabled]

Controller.

 

 

Serial Port Address

[3F8 / IRQ4]

 

 

Infrared Port Address

[Disabled]

 

 

Parallel Port Address

[378]

 

 

Parallel Port Mode

[ECP + EPP]

 

 

EPP Version

[1.9]

 

 

ECP Mode DMA Channel

[DMA3]

 

 

Parallel Port IRQ

[IRQ7]

 

 

OnBoard Game Port

[Enabled]

 

Select Screen

OnBoard MIDI Port

[Disabled]

 

 

Select Item

 

 

 

 

 

+-

Change Option

 

 

F1

General Help

 

 

F9

Load Defaults

 

 

F10

Save and Exit

 

 

ESC

Exit

v02.54 (C) Copyright 1985-2005, American Megatrends, Inc.

OnBoard Floppy Controller

Use this item to enable or disable floppy drive controller.

Serial Port Address

Use this item to set the address for the onboard serial port or disable it. Configuration options: [Disabled], [3F8 / IRQ4], [2F8 / IRQ3], [3E8 / IRQ4], [2E8 / IRQ3].

Infrared Port Address

Use this item to set the address for the onboard infrared port or disable it. Configuration options: [Disabled], [2F8 / IRQ3], and [2E8 / IRQ3].

3 6

Image 36
Contents ConRoe945PL-GLAN Copyright Notice DisclaimerContents Software Support Package Contents IntroductionSpecifications Connector Bios FeatureSee Caution Support CDPage CPU Motherboard Layout 19.1cm 7.5HD 8CH I/O Panel Table for Audio Output ConnectionPre-installation Precautions Screw HolesCPU Installation Page Installation of CPU Fan and Heatsink Installation of Memory Modules Dimm Installing a DimmInstalling an expansion card Expansion Slots PCI and PCI Express SlotsJumpers Setup PS2USBPWR1Onboard Headers and Connectors USB 2.0 Headers Chassis Speaker Header Black end White end 2-pin Hdmispdif Header Connection Guide Sataii Hard Disk Setup Guide Western DigitalDriver Installation Guide Untied Overclocking TechnologyBios Menu Bar Navigation Keys Main ScreenAdvanced Screen CPU Configuration Boot Failure GuardCPU Host Frequency Spread SpectrumRatio Cmos Setting Ratio Actual ValueEnhance Halt State Max Cpuid Value LimitChipset Configuration Boot Graphic Adapter Priority Dram RAS# Activate to PrechargeOnBoard HD Audio Front Panel ControlAcpi Configuration IDE Configuration ATA/IDE ConfigurationIDE Device Configuration Combined OptionLBA/Large Mode PIO ModeDMA Mode Block Multi-Sector TransferPCIPnP Configuration PCI Latency TimerA.R.T Bit Data TransferFloppy Configuration Super IO ConfigurationOnBoard Floppy Controller Serial Port AddressParallel Port Mode ECP Mode DMA ChannelParallel Port Address EPP VersionUSB Configuration Hardware Health Event Monitoring ScreenUSB Controller USB 2.0 SupportBoot Screen Target CPU Temperature CCPU Quiet Fan Tolerance CBoot Settings Configuration Boot From NetworkBoot Up Num-Lock Security ScreenLoad Optimal Defaults Exit ScreenSave Changes and Exit Discard Changes and ExitInstall Operating System LGA 775 CPU Installation Live Demo ProgramSupport CD Information Running The Support CD