MSI 848P NEO-V - Motherboard - ATX manual Serial ATA HDD Connectors SATA1, SATA2

Page 27

MS-6788 ATX Mainboard

Serial ATA HDD Connectors: SATA1, SATA2

The mainboard provides dual high-speed Serial ATA interface ports. The ports support 1st generation Serial ATA data rates of 150MB/s and are fully compliant with Serial ATA 1.0 specifications. Each Serial ATA connector can connect to 1 hard disk drive.

SATA2

Definition

SIGNAL

GND

TXP

TXN

GND

RXN

RXP

SATA1

GND

Take out the dust cover and connect to the hard disk devices

Optional Serial ATA cable

Connect to SATA1 or SATA2

MSI Reminds You...

Please do not fold the Serial ATA cable into 90-degree angle. Otherwise, the loss of data may occur during transmission.

2-16

Image 27

Contents 865PE Neo2-V / 848P Neo-V Series FCC-B Radio Frequency Interference Statement Voir LA Notice D’INSTALLATION Avant DE Raccorder AU ReseauRevision Revision History Date Copyright NoticeTrademarks Revision HistoryTechnical Support Safety InstructionsContents Clear Cmos Jumper JBAT1 Getting Started Slots Mainboard SpecificationsChipset Main MemoryLAN Optional DimensionOn-Board Peripherals AudioChipset Mainboard Layout848P Neo-V MS-6788 v2.X ATX Mainboard Hardware Setup SYSFAN1 , p.2-14 Quick Components GuideThen Example of CPU Core Speed Derivation ProcedureCentral Processing Unit CPU Memory Speed/CPU FSB Support MatrixCPU Installation Procedures for Socket Installing the CPU Fan Fan power cable DIMM1 DIMM2 MemoryIntroduction to DDR Sdram DDR Population RulesDual-channel DDR Introduction Installing DDR ModulesATX1 Power SupplyATX 20-Pin Power Connector ATX1 ATX 12V Power Connector JPW1PS/2 Mouse 6-pin Female PS/2 Keyboard 6-pin Female Mouse ConnectorKeyboard Connector Back PanelSerial Port Connector COM a USB ConnectorsSPDIF-out Port Connector MIC Audio Port ConnectorsLine Stereo Audio Connectors Line Out RJ-45 LAN JackParallel Port Connector LPT1 CD-In Connector CD1 ConnectorsFloppy Disk Drive Connector FDD1 Fan Power Connectors CPUFAN1/SYSFAN1ATA100 Hard Disk Connectors IDE1 & IDE2 Front USB Connectors JUSB2 & JUSB3MSI Reminds You Serial ATA HDD Connectors SATA1, SATA2 SATA2SATA1 JSP1 Bracket Spdif Connector JSP1 OptionalJFP1 JFP2 Front Panel Connectors JFP1 & JFP2JAUD1 Front Panel Audio Connector JAUD1Bracket 2 Connector JDB1 Optional JDB1Bracket Jumpers Clear Cmos Jumper JBAT1JBAT1 PCI Interrupt Request Routing SlotsAGP Accelerated Graphics Port Slot PCI Peripheral Component Interconnect SlotsBios Setup Selecting the First Boot Device Entering SetupMain Menu Default SettingsControl Keys Getting HelpMain Menu Load Bios Setup Defaults Set Supervisor PasswordSet User Password Load High Performance DefaultsStandard Cmos Features Floppy Drive a Advanced Bios Features A.R.T. for Hard Disks BootUp Num-LockPassword Check Boot To OS/2CPU L1 & L2 Cache System Bios CacheableMPS Revision Apic Acpi SCI IRQCAS# Latency Advanced Chipset FeaturesDram Timing Setting Configure Sdram Timing by SPDBurst Length RAS# to CAS# DelayPrecharge Delay RAS# PrechargePower Management Features Re-Call VGA Bios at S3 ResumingAcpi Standby State Set Monitor Events Power Management/APMPower Button Function Suspend Time Out MinuteResume On RTC Alarm Keyboard PowerOn FunctionSpecific Key for PowerOn Mouse PowerOn FunctionInit. Graphics Adapter Priority PNP/PCI ConfigurationsPCI Latency Timer PCI Clocks Clear NvramSet DMAs to PnP or ISA PCI IDE BusMasterSet IRQs to PCI or ISA IRQ 3/4/5/7/9/10/11/14/15DMA Channel 0/1/3/5/6/7 USB Controller On-Chip IDE ConfigurationOn-Chip ATAs Operate Mode Integrated PeripheralsATA Channel Selection ATA ConfigurationATA Keep Enabled Combined Mode OptionSet Super I/O Parallel Port ModeOnBoard LAN AC’97 AudioEPP Version Parallel Port IRQParallel Port DMA Channel PC Health Status Dynamic OverClocking Frequency/Voltage ControlSpread Spectrum Performance ModeCPU Ratio Selection Dram FrequencyDDR Power Voltage Adjust CPU Bus Clock MhzAdjust AGP/PCI Clock Mhz CPU Vcore AdjustSet Supervisor/User Password Load High Performance/BIOS Setup Defaults