MSI 848P NEO-V - Motherboard - ATX Set Supervisor Password, Set User Password, Save & Exit Setup

Page 38

BIOS Setup

Set Supervisor Password

Use this menu to set Supervisor Password.

Set User Password

Use this menu to set User Password.

Load High Performance Defaults

Use this menu to load the BIOS values for the best system performance, but the system stability may be affected.

Load BIOS Setup Defaults

Use this menu to load factory default settings into the BIOS for stable system perfor- mance operations.

Save & Exit Setup

Save changes to CMOS and exit setup.

Exit Without Saving

Abandon all changes and exit setup.

3 - 5

Image 38

Contents 865PE Neo2-V / 848P Neo-V Series Voir LA Notice D’INSTALLATION Avant DE Raccorder AU Reseau FCC-B Radio Frequency Interference StatementRevision History Copyright NoticeTrademarks Revision Revision History DateSafety Instructions Technical SupportContents Clear Cmos Jumper JBAT1 Getting Started Main Memory Mainboard SpecificationsChipset SlotsAudio DimensionOn-Board Peripherals LAN OptionalMainboard Layout Chipset848P Neo-V MS-6788 v2.X ATX Mainboard Hardware Setup Quick Components Guide SYSFAN1 , p.2-14Memory Speed/CPU FSB Support Matrix Example of CPU Core Speed Derivation ProcedureCentral Processing Unit CPU ThenCPU Installation Procedures for Socket Installing the CPU Fan Fan power cable DDR Population Rules MemoryIntroduction to DDR Sdram DIMM1 DIMM2Installing DDR Modules Dual-channel DDR IntroductionATX 12V Power Connector JPW1 Power SupplyATX 20-Pin Power Connector ATX1 ATX1Back Panel Mouse ConnectorKeyboard Connector PS/2 Mouse 6-pin Female PS/2 Keyboard 6-pin FemaleSPDIF-out Port Connector Serial Port Connector COM aUSB Connectors RJ-45 LAN Jack Audio Port ConnectorsLine Stereo Audio Connectors Line Out MICParallel Port Connector LPT1 Fan Power Connectors CPUFAN1/SYSFAN1 ConnectorsFloppy Disk Drive Connector FDD1 CD-In Connector CD1MSI Reminds You ATA100 Hard Disk Connectors IDE1 & IDE2Front USB Connectors JUSB2 & JUSB3 SATA1 Serial ATA HDD Connectors SATA1, SATA2SATA2 Bracket Spdif Connector JSP1 Optional JSP1Front Panel Connectors JFP1 & JFP2 JFP1 JFP2Front Panel Audio Connector JAUD1 JAUD1Bracket Bracket 2 Connector JDB1 OptionalJDB1 JBAT1 JumpersClear Cmos Jumper JBAT1 PCI Peripheral Component Interconnect Slots SlotsAGP Accelerated Graphics Port Slot PCI Interrupt Request RoutingBios Setup Entering Setup Selecting the First Boot DeviceGetting Help Default SettingsControl Keys Main MenuMain Menu Load High Performance Defaults Set Supervisor PasswordSet User Password Load Bios Setup DefaultsStandard Cmos Features Floppy Drive a Advanced Bios Features Boot To OS/2 BootUp Num-LockPassword Check A.R.T. for Hard DisksApic Acpi SCI IRQ System Bios CacheableMPS Revision CPU L1 & L2 CacheConfigure Sdram Timing by SPD Advanced Chipset FeaturesDram Timing Setting CAS# LatencyRAS# Precharge RAS# to CAS# DelayPrecharge Delay Burst LengthAcpi Standby State Power Management FeaturesRe-Call VGA Bios at S3 Resuming Suspend Time Out Minute Power Management/APMPower Button Function Set Monitor EventsMouse PowerOn Function Keyboard PowerOn FunctionSpecific Key for PowerOn Resume On RTC AlarmClear Nvram PNP/PCI ConfigurationsPCI Latency Timer PCI Clocks Init. Graphics Adapter PriorityIRQ 3/4/5/7/9/10/11/14/15 PCI IDE BusMasterSet IRQs to PCI or ISA Set DMAs to PnP or ISADMA Channel 0/1/3/5/6/7 Integrated Peripherals On-Chip IDE ConfigurationOn-Chip ATAs Operate Mode USB ControllerCombined Mode Option ATA ConfigurationATA Keep Enabled ATA Channel SelectionAC’97 Audio Parallel Port ModeOnBoard LAN Set Super I/OParallel Port DMA Channel EPP VersionParallel Port IRQ PC Health Status Frequency/Voltage Control Dynamic OverClockingDram Frequency Performance ModeCPU Ratio Selection Spread SpectrumCPU Vcore Adjust Adjust CPU Bus Clock MhzAdjust AGP/PCI Clock Mhz DDR Power VoltageSet Supervisor/User Password Load High Performance/BIOS Setup Defaults