MSI 848P NEO-V - Motherboard - ATX manual Entering Setup, Selecting the First Boot Device

Page 35

MS-6788 ATX Mainboard

Entering Setup

Power on the computer and the system will start POST (Power On Self Test) process. When the message below appears on the screen, press <DEL> key to enter Setup.

DEL: Setup

F11: Boot Menu

F12: Network boot

TAB: Logo

If the message disappears before you respond and you still wish to enter Setup, restart the system by turning it OFF and On or pressing the RESET button. You may also restart the system by simultaneously pressing <Ctrl>, <Alt>, and <Delete> keys.

Selecting the First Boot Device

You are allowed to select the 1st boot device without entering the BIOS setup utility by pressing <F11>. When the same message as listed above appears on the screen, press <F11> to trigger the boot menu.

The POST messages might pass by too quickly for you to respond in time. If so, restart the system and press <F11> after around 2 or 3 seconds to activate the boot menu similar to the following.

Select First Boot Device

Floppy	: 1st Floppy
IDE-0	: IBM-DTLA-307038
CDROM	: ATAPI CD-ROM DRIVE 40X M

[Up/Dn] Select	[RETURN] Boot	[ESC] cancel

The boot menu will list all the bootable devices. Select the one you want to boot from by using arrow keys, then press <Enter>. The system will boot from the se- lected device. The selection will not make changes to the settings in the BIOS setup utility, so next time when you power on the system, it will still use the original first boot device to boot up.

3 - 2

Image 35

Contents 865PE Neo2-V / 848P Neo-V Series FCC-B Radio Frequency Interference Statement Voir LA Notice D’INSTALLATION Avant DE Raccorder AU ReseauRevision Revision History Date Copyright NoticeTrademarks Revision HistoryTechnical Support Safety InstructionsContents Clear Cmos Jumper JBAT1 Getting Started Slots Mainboard SpecificationsChipset Main MemoryLAN Optional DimensionOn-Board Peripherals AudioChipset Mainboard Layout848P Neo-V MS-6788 v2.X ATX Mainboard Hardware Setup SYSFAN1 , p.2-14 Quick Components GuideThen Example of CPU Core Speed Derivation ProcedureCentral Processing Unit CPU Memory Speed/CPU FSB Support MatrixCPU Installation Procedures for Socket Installing the CPU Fan Fan power cable DIMM1 DIMM2 MemoryIntroduction to DDR Sdram DDR Population RulesDual-channel DDR Introduction Installing DDR ModulesATX1 Power SupplyATX 20-Pin Power Connector ATX1 ATX 12V Power Connector JPW1PS/2 Mouse 6-pin Female PS/2 Keyboard 6-pin Female Mouse ConnectorKeyboard Connector Back PanelSPDIF-out Port Connector Serial Port Connector COM aUSB Connectors MIC Audio Port ConnectorsLine Stereo Audio Connectors Line Out RJ-45 LAN JackParallel Port Connector LPT1 CD-In Connector CD1 ConnectorsFloppy Disk Drive Connector FDD1 Fan Power Connectors CPUFAN1/SYSFAN1MSI Reminds You ATA100 Hard Disk Connectors IDE1 & IDE2Front USB Connectors JUSB2 & JUSB3 SATA1 Serial ATA HDD Connectors SATA1, SATA2SATA2 JSP1 Bracket Spdif Connector JSP1 OptionalJFP1 JFP2 Front Panel Connectors JFP1 & JFP2JAUD1 Front Panel Audio Connector JAUD1Bracket Bracket 2 Connector JDB1 OptionalJDB1 JBAT1 JumpersClear Cmos Jumper JBAT1 PCI Interrupt Request Routing SlotsAGP Accelerated Graphics Port Slot PCI Peripheral Component Interconnect SlotsBios Setup Selecting the First Boot Device Entering SetupMain Menu Default SettingsControl Keys Getting HelpMain Menu Load Bios Setup Defaults Set Supervisor PasswordSet User Password Load High Performance DefaultsStandard Cmos Features Floppy Drive a Advanced Bios Features A.R.T. for Hard Disks BootUp Num-LockPassword Check Boot To OS/2CPU L1 & L2 Cache System Bios CacheableMPS Revision Apic Acpi SCI IRQCAS# Latency Advanced Chipset FeaturesDram Timing Setting Configure Sdram Timing by SPDBurst Length RAS# to CAS# DelayPrecharge Delay RAS# PrechargeAcpi Standby State Power Management FeaturesRe-Call VGA Bios at S3 Resuming Set Monitor Events Power Management/APMPower Button Function Suspend Time Out MinuteResume On RTC Alarm Keyboard PowerOn FunctionSpecific Key for PowerOn Mouse PowerOn FunctionInit. Graphics Adapter Priority PNP/PCI ConfigurationsPCI Latency Timer PCI Clocks Clear NvramSet DMAs to PnP or ISA PCI IDE BusMasterSet IRQs to PCI or ISA IRQ 3/4/5/7/9/10/11/14/15DMA Channel 0/1/3/5/6/7 USB Controller On-Chip IDE ConfigurationOn-Chip ATAs Operate Mode Integrated PeripheralsATA Channel Selection ATA ConfigurationATA Keep Enabled Combined Mode OptionSet Super I/O Parallel Port ModeOnBoard LAN AC’97 AudioParallel Port DMA Channel EPP VersionParallel Port IRQ PC Health Status Dynamic OverClocking Frequency/Voltage ControlSpread Spectrum Performance ModeCPU Ratio Selection Dram FrequencyDDR Power Voltage Adjust CPU Bus Clock MhzAdjust AGP/PCI Clock Mhz CPU Vcore AdjustSet Supervisor/User Password Load High Performance/BIOS Setup Defaults