MSI 848P NEO-V - Motherboard - ATX manual Integrated Peripherals, USB Controller

Page 52

BIOS Setup

Integrated Peripherals

Please note that the options showed on your BIOS might be different de- pending on the motherboard you buy.

USB Controller

This setting is used to enable/disable the onboard USB controllers. Setting options: [Disabled], [Enabled].

USB Device Legacy Support

Set to [Enabled] if your need to use any USB 1.1/2.0 device in the operating system that does not support or have any USB 1.1/2.0 driver installed, such as DOS and SCO Unix. Set to [Disabled] only if you want to use any USB device other than the USB mouse. Setting options: [Disabled], [Enabled].

On-Chip IDE Configuration

Press <Enter> to enter the sub-menu and the following screen appears:

On-Chip ATA(s) Operate Mode

This setting allows you to determine how the RAID controller on the south bridge is going to switch to SATA controller. [Legacy Mode] means you may use the traditional 14 and 15 IRQs, while [Native Mode] means you may use all the available IRQs. Setting options: [Legacy Mode], [Native Mode].

3-19

Image 52

Contents 865PE Neo2-V / 848P Neo-V Series Voir LA Notice D’INSTALLATION Avant DE Raccorder AU Reseau FCC-B Radio Frequency Interference StatementCopyright Notice TrademarksRevision History Revision Revision History DateSafety Instructions Technical SupportContents Clear Cmos Jumper JBAT1 Getting Started Mainboard Specifications ChipsetMain Memory SlotsDimension On-Board PeripheralsAudio LAN OptionalMainboard Layout Chipset848P Neo-V MS-6788 v2.X ATX Mainboard Hardware Setup Quick Components Guide SYSFAN1 , p.2-14Example of CPU Core Speed Derivation Procedure Central Processing Unit CPUMemory Speed/CPU FSB Support Matrix ThenCPU Installation Procedures for Socket Installing the CPU Fan Fan power cable Memory Introduction to DDR SdramDDR Population Rules DIMM1 DIMM2Installing DDR Modules Dual-channel DDR IntroductionPower Supply ATX 20-Pin Power Connector ATX1ATX 12V Power Connector JPW1 ATX1Mouse Connector Keyboard ConnectorBack Panel PS/2 Mouse 6-pin Female PS/2 Keyboard 6-pin FemaleUSB Connectors Serial Port Connector COM aSPDIF-out Port Connector Audio Port Connectors Line Stereo Audio Connectors Line OutRJ-45 LAN Jack MICParallel Port Connector LPT1 Connectors Floppy Disk Drive Connector FDD1Fan Power Connectors CPUFAN1/SYSFAN1 CD-In Connector CD1Front USB Connectors JUSB2 & JUSB3 ATA100 Hard Disk Connectors IDE1 & IDE2MSI Reminds You SATA2 Serial ATA HDD Connectors SATA1, SATA2SATA1 Bracket Spdif Connector JSP1 Optional JSP1Front Panel Connectors JFP1 & JFP2 JFP1 JFP2Front Panel Audio Connector JAUD1 JAUD1JDB1 Bracket 2 Connector JDB1 OptionalBracket Clear Cmos Jumper JBAT1 JumpersJBAT1 Slots AGP Accelerated Graphics Port SlotPCI Peripheral Component Interconnect Slots PCI Interrupt Request RoutingBios Setup Entering Setup Selecting the First Boot DeviceDefault Settings Control KeysGetting Help Main MenuMain Menu Set Supervisor Password Set User PasswordLoad High Performance Defaults Load Bios Setup DefaultsStandard Cmos Features Floppy Drive a Advanced Bios Features BootUp Num-Lock Password CheckBoot To OS/2 A.R.T. for Hard DisksSystem Bios Cacheable MPS RevisionApic Acpi SCI IRQ CPU L1 & L2 CacheAdvanced Chipset Features Dram Timing SettingConfigure Sdram Timing by SPD CAS# LatencyRAS# to CAS# Delay Precharge DelayRAS# Precharge Burst LengthRe-Call VGA Bios at S3 Resuming Power Management FeaturesAcpi Standby State Power Management/APM Power Button FunctionSuspend Time Out Minute Set Monitor EventsKeyboard PowerOn Function Specific Key for PowerOnMouse PowerOn Function Resume On RTC AlarmPNP/PCI Configurations PCI Latency Timer PCI ClocksClear Nvram Init. Graphics Adapter PriorityPCI IDE BusMaster Set IRQs to PCI or ISAIRQ 3/4/5/7/9/10/11/14/15 Set DMAs to PnP or ISADMA Channel 0/1/3/5/6/7 On-Chip IDE Configuration On-Chip ATAs Operate ModeIntegrated Peripherals USB ControllerATA Configuration ATA Keep EnabledCombined Mode Option ATA Channel SelectionParallel Port Mode OnBoard LANAC’97 Audio Set Super I/OParallel Port IRQ EPP VersionParallel Port DMA Channel PC Health Status Frequency/Voltage Control Dynamic OverClockingPerformance Mode CPU Ratio SelectionDram Frequency Spread SpectrumAdjust CPU Bus Clock Mhz Adjust AGP/PCI Clock MhzCPU Vcore Adjust DDR Power VoltageSet Supervisor/User Password Load High Performance/BIOS Setup Defaults