Raypak 0135A, 0195A, 0090A Electrical Wiring, Relief Valve, Temperature & Pressure Gauge

Page 13

When this water heater system is supplying general purpose hot water requirements for use by individuals, a thermostatically controlled mixing valve is recom- mended to reduce the risk of scald injury. Contact a licensed plumber or the local plumbing authority for further information.

Thermometer(s) should be installed so that they indi- cate the water temperature at or near the outlet of the storage tank.

Relief Valve

A new combination temperature and pressure (T & P) relief valve, complying with the Standard for Relief Valves and Automatic Gas Shut Off Devices for Hot Water Supply Systems, ANSI Z21.22, must be installed in the opening provided on top of the storage tank, at the time of installation. No valve is to be placed between the relief valve and the storage tank.

The pressure rating of the relief valve must not exceed the 160 maximum working pressure indicated on the water heater rating plate. The BTUH rating of the relief valve must not be less than the BTUH input of the heater.

Connect the outlet of the relief valve to a suitable open drain. The discharge line must pitch downward from the valve to allow complete draining (by gravity) of the relief valve and discharge line.

The discharge line should be no smaller than the out- let of the valve. The end of the discharge line should not be threaded or concealed, and should be protect- ed from freezing. No valve of any type, restriction or reducer coupling, should be installed in the discharge line. Local codes shall govern installation of relief valve.

Temperature & Pressure Gauge

The temperature and pressure gauge is standard equipment on all hot water heaters. All temperature and pressure gauges are shipped loose for field instal- lation in the outlet water connection (see Fig. 7). All fittings required to mount the gauge to the piping are supplied by others.

Electrical Wiring

The electrical power supply requirement for these heaters is 120 volts, 60 Hz. Field wiring connections and electrical grounding must comply with the local codes, or in the absence of local codes, with the latest edition of the National Electrical Code, ANSI/NFPA 70.

Provide a separate fused circuit from the main electri- cal panel to the heater, and a disconnecting means within sight of the heater.

Remove the control box cover and make the power supply connections in the field wiring compartment. (See general location of controls drawing). The pump is supplied and factory wired to operate with the heater. The thermostat (tankstat) is shipped loose to be installed in the tank at the installation site.

WARNING: SHOCK HAZARD: Line voltage is present. Before servicing tankstat or heater, turn off electrical power to the heater at the main disconnect or circuit breaker. Failure to do so could result in severe personal injury or death.

NOTE: Minimum 18 AWG, 105°C, stranded wire must be used for all low voltage (less than 30 volts) external connections to the unit. Solid conductors should not be used because they can cause excessive tension on contact points. Install conduit as appropriate. All high voltage wires must be the same size (105°C, stranded wire) as the ones on the unit or larger.

NOTE: If it is necessary to replace any of the original wiring, it must be replaced with 105°C wire or its equivalent, except 150° black wire which must be replaced with 150° wire or its equivalent.

13

Image 13
Contents Econopak Water Heaters Page Contents Be corrected. When smelling to detect an propane Solution to check all gas fittings and connectionsCations and their installation should be Are important but not related to personal injury hazardsTime/Temperature Relationships in Scalds General SafetyTemperature Time to Produce Serious Burn Receiving Equipment General SpecificationsInput Recovery Tank Piping Connections DimensionsGph Gal Water Gas Vent WH-0090 WH-0135 132 WH-0195 192Code Requirements InstallationMounting Base ClearancesVenting Connections Vent Max Model No Connector Horizontal Diameter Length ftModel No Sq. in. of Each Free Area 0090 0135 0195Venting Minimum Clearances Common VentsModel No Nat Pro Gas Supply Connections0090 125 300 400 560 0135 150 200 0195 100 Setting Gas Pressure Specifications Type Inches WC Regulator MinWater Connections & System Piping Natural 10.5 Propane 12.0 13.0 11.0Temperature & Pressure Gauge Electrical WiringRelief Valve Wiring Diagram-Standing Pilot-Models 0090, 0135 Wiring Diagram-IID-Models 0090, 0135 Start-up Procedures Servicing ProceduresSequence of Operation Honeywellpilot Robertshaw Pilot Lighting the Heater System Shut Down ProcedureFor Standing Pilot Models For Automatic Ignition ModelsFor Honeywell Gas Valve Turn gas control knob To Turn Off Gas to HeaterCounter-clockwise to on All ModelsInspection Procedures Testing the Ignition Safety Shut-offProcedure for Cleaning Flue Gas Passage Ways Normal Inspection ProceduresBurner Drawer Removal Main Burner and Orifice RemovalHeat Exchanger Re-Assembly Tube Cleaning Procedure TypicalRepair Section Heat Exchanger RemovalCauses TroubleshootingPiping Adjustments & Replacement of Components Replacement Parts Circulator ReplacementEastman Avenue Oxnard, CA Limitedpartswarrantyeconopakwaterheaters

0090A, 0135A, 0195A specifications

Raypak is a leading manufacturer in the pool and spa industry, known for its reliable and innovative heating solutions. Among its product line, the Raypak 0090A, 0135A, and 0195A are notable models that stand out for their efficiency, durability, and advanced technology.

The Raypak 0090A is ideal for residential pools, offering a heat output of 90,000 BTU per hour. It utilizes a copper heat exchanger, which provides efficient heat transfer and is resistant to corrosion, making it perfect for chlorinated pools. This model features a digital thermostat that enhances user control, allowing for precise temperature settings. Additionally, the 0090A is compatible with both natural gas and propane, providing flexibility depending on user preference.

The Raypak 0135A, with its 135,000 BTU output, is designed for larger residential pools or smaller commercial applications. This model employs advanced energy-efficient technology, helping to reduce operational costs while maintaining optimal heating performance. One of the key features of the 0135A is its built-in electronic ignition system, which improves reliability and eliminates the need for a standing pilot, enhancing safety and efficiency. The unit's compact design allows it to fit in tight spaces while still providing robust heating capabilities.

The Raypak 0195A is the most powerful of the trio, delivering 195,000 BTU, making it suitable for larger pool setups and high-demand environments. It also uses a copper heat exchanger, ensuring excellent heat retention and durability against corrosion. The 0195A is equipped with an easy-to-use digital display, offering intuitive controls for temperature adjustments and operational monitoring. This model also incorporates a high-tech air intake design, which maximizes airflow and reduces energy consumption.

All three models are designed for outdoor installation and possess weather-resistant features, ensuring longevity and reliability through various environmental conditions. Additionally, they are equipped with easy access service panels for maintenance, ensuring that servicing is efficient and straightforward.

In summary, Raypak's 0090A, 0135A, and 0195A models are designed to meet diverse heating needs with advanced technology, energy efficiency, and robust construction, making them excellent choices for anyone looking to enhance their pool experience.